GBC StreamPunch Ultra Service Manual page 275

General Procedures and Information
Section Contents
Title
General Procedures ...................................................................... 3
User Interface ............................................................................... 3
Settings ..................................................................................... 4
Information ................................................................................ 4
User Interface Screen Map ...................................................... 5
GP 6.1 User Interface Procedure ...................................... 6
Settings Procedure ................................................................... 6
GP 6.1.1 BACKGAGE SETTING Procedure ........................7
GP 6.1.2 ALIGNMENT SETTING Procedure ........................9
GP 6.1.3 CLEAR COVER Procedure ................................ 11
GP 6.1.4 LANGUAGE SETTINGS Procedure ................... 13
GP 6.1.5 UNITS Procedure ................................................ 14
GP 6.1.7 INFORMATION Procedure ................................. 15
GP 6.1.8 DIE TYPE Procedure .......................................... 16
GP 6.1.9 DIE CYCLES Procedure ..................................... 17
GP 6.1.10 PUNCH CYCLES Procedure .............................. 18
GP 6.1.11 FIRMWARE Procedure ....................................... 19
Service User Interface ................................................................ 20
Service Interface Screen Map ................................................ 22
GP 6.2 Service User Interface Procedure ....................... 23
GP 6.2.1 PAPER SIZE Setting........................................... 24
GP 6.2.2 MAX BYPASS Setting......................................... 25
GP 6.2.3 RUN MODE Setting ............................................ 26
GP 6.2.4 DIE CYCLES ....................................................... 27
GP 6.2.5 SENSORS Check ............................................... 28
GP 6.2.6 SOLENOIDS Check ............................................ 31
GP 6.2.7 MOTORS Check ................................................. 32
GP 6.2.8 FUNCTION TESTS (Cycle Punch, Aligner Test, Fan
Test) .................................................................... 33
GP 6.2.9 SKEW OFFSETS Adjustment ............................. 35
GP 6.2.10 ALIGN OFFSETS Adjustment ............................ 39
GP 6.2.11 LOG..................................................................... 41
GP 6.2.12 FIRMWARE UPGRADE Procedure .................... 42
GP 6.3 Undock the Punch (Moving the punch to Service position)
............................................................................ 44
GP 6.4 Dock the punch (Moving the punch to Operating position)
............................................................................ 44
GP 6.5 Operational Inspection ........................................ 45
GBC StreamPunch Ultra/Ultra MP
Page
GP 6.6
GP 6.7
GP 6.7.1
GP 6.7.2
GP 6.7.3
GP 6.7.4
GP 6.8
GP 6.9
GP 6.10
GP 6.11
GP 6.12
GP 6.13
GP 6.14
GP 6.14.1 Idler Roller Cleaning ............................................ 53
GP 6.14.2 Steering Idler Roller and Springs Inspection and Cleaning
GP 6.15
Cleaning ............................................................................ 55
GP 6.16
GP 6.17
GP 6.18
GP 6.19
GP 6.20
GP 6.21
GP 6.22
GP 6.23
GP 6.24
GP 6.25
GP 6.26
GP 6.27
General Information .................................................................... 69
Principle of Operation ................................................................. 69
Punch Path ................................................................................. 69
Single Punch ........................................................................... 69
11-05-2018
6-1
Internal Inspection ............................................... 45
Die Set Service ................................................... 46
Die Set Life Expectancy ...................................... 46
Die Set Components ........................................... 46
Die Set Lubrication .............................................. 47
Die Set Shoulder Bolts ........................................ 48
External Cleaning ................................................ 49
Internal Cleaning ................................................. 49
Base Cleaning ..................................................... 50
Chip Bin Cleaning ............................................... 50
Die Guide Cleaning ............................................. 51
Door Latch Inspection ......................................... 51
Idler Roller and Idler Springs Inspection ............. 52
............................................................................ 54
. Drive Roller and Steering Drive Roller Inspection and
Panel Latch Inspection ........................................ 56
Optical Sensor Cleaning ..................................... 59
Bypass Paper Path Inspection and Cleaning...... 60
Punch Paper Path Inspection and Cleaning ....... 61
Punch Drive Cam Lubrication ............................. 62
Timing Belt Inspection ......................................... 63
Solenoid Cleaning and Inspection ...................... 64
Alignment Carriage Rails Cleaning ..................... 65
Punch Clutch Inspection and Cleaning ............... 65
Diverter Solenoid Assembly Inspection .............. 66
Die Set Recognition Board Clips Inspection ....... 67
Die Lock Mechanism and Die Rail Springs Inspection 67
General Procedures and Information
Section Contents