Canon imageRUNNER ADVANCE 8105 Series Service Manual page 884

COPIER > OPTION > USER
PR-PSESW Display/hide of output Stop button
Lv.1 Details To set whether to display or hide [Stop] button on the Status Monitor
screen.
Use case - Upon user's request
- When promptly stopping the print job in operation or under
reservation
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Hide, 1: Display
Default value 0
IDPRN-SW Charge target job set of dept mngm cntr
Lv.1 Details To set the job type that advances the department management
counter.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0:
PRINT category: Inbox Print, Report Print, Send Local Print, PDL
Print
COPY category: COPY
1:
PRINT category: Report Print, Send Local Print, PDL Print
COPY category: COPY, Inbox Print
Default value 0
PCL-COPY Set of PCL COPIES command control method
Lv.2 Details To set the binder control method of COPIES command with PCL.
Select whether to use the control method of Canon-made PCL or
use the same control method of non-Canon-made PCL.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 65535
0: Control method of Canon-made PCL (following the value of
COPIES command that is specified for each page to control on a
page basis)
1: Control method of non-Canon-made PCL (handling the value
of COPIES command, which is specified for page 1 at the time of
Collate mode, as bind figure while the value of COPIES command
for the next page or later is invalid. Same control applies as Canon-
made PCL at the time of non-sorted mode)
2 to 65535: For future use
Default value 0
8
Service Mode > COPIER > OPTION > USER
8
Service Mode > COPIER > OPTION > USER
COPIER > OPTION > USER
CNT-SW Set default dis items on charge counter
Lv.1 Details To set default display items of the charge counter on the Counter
Check screen.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Do not use this mode overseas (outside Japan).
Display/adj/set range 0 to 2
For Japan
0: Counter 1 - Total 1: 101
1: Counter 1 - Total 2: 102, Counter 2 - Copy (Total 2): 202, Counter
3 - Total A2: 127
2: Not used
For UL
0: Counter 1 - Total 1: 101, Counter 2 - Total (Large): 103, Counter
3 - Copy (Total 1): 201, Counter 4 - Copy (Large): 203
1: Counter 1 - Total 2: 102, Counter 2 - Copy (Total 2): 202
2: Not used
Default value 0
TAB-ACC Auto cassette change set for tab paper
Lv.1 Details To set to enable/disable auto cassette change when tab paper runs
out.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to instruct the user to thoroughly comply the following:
- Use tab paper with the same number of tabs.
- Set tab paper.
Be sure to comply the above; otherwise, proper print is not available
and it can cause soil inside the machine because of toner.
Display/adj/set range 0 to 1
0: Auto cassette change disabled, 1: Auto cassette change enabled
Default value 1
REMPNL ON/OFF of remote panel function
Lv.1 Details To set ON/OFF of remote panel function.
When ON is set, the operation like the Control Panel is enabled from
PC.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Do not use this mode overseas (outside Japan).
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
8-169
8-169