Canon imageRUNNER ADVANCE 8105 Series Service Manual page 745

COPIER > DISPLAY > ACC-STS
DATA-CON Dis of NE Controller connection state
Lv.1 Details To display the connecting state of NE Controller.
Use case When checking the connection between the machine and the NE
Controller
Adj/set/operate method N/A (Display only)
Display/adj/set range 0 to 1
0: Not connected, 1: Connected
RAM Display of MNCON PCB memory capacity
Lv.1 Details To display the memory capacity of the Main Controller PCB.
Use case When checking the memory capacity of the machine
Adj/set/operate method N/A (Display only)
Unit MB
Default value 512
COINROBO Dis of Coin Manager connection state
Lv.1 Details To display the connecting state of the Coin Manager.
Use case When checking the connection between the machine and the Coin
Manager
Adj/set/operate method N/A (Display only)
Display/adj/set range 0 to 1
0: Not connected, 1: Connected
NIB Display of Network PCB connection state
Lv.1 Details To display the connecting state of the Network PCB.
Use case When checking the connection between the machine and the
Network PCB
Adj/set/operate method N/A (Display only)
Display/adj/set range 0 to 3
0: Not connected, 1: Ethernet PCB connected, 2: Token Ring PCB
connected, 3: Ethernet PCB + Token Ring PCB connected
Install state dis of PS/PCL firmware
PS/PCL
To display the installation state of PS/PCL firmware.
Lv.1 Details
When checking whether NetWare firmware is installed to the
Use case
machine
Adj/set/operate method N/A (Display only)
Display/adj/set range 0 to 2
0: Not installed, 1: PS/PCL, 2: PS Kanji
Dis of NetWare firmware install state
NETWARE
To display the installation state of the NetWare firmware.
Lv.1 Details
When checking whether NetWare firmware is installed to the
Use case
machine
Adj/set/operate method N/A (Display only)
Display/adj/set range 0 to 1
0: Not installed, 1: Installed
8
Service Mode > COPIER > DISPLAY > ACC-STS
8
Service Mode > COPIER > DISPLAY > ACC-STS
COPIER > DISPLAY > ACC-STS
SEND Display of SEND support PCB existence
Lv.1 Details To display whether there is PCB to support SEND function.
SEND function can be used only when the PCB is mounted.
Use case When checking the connection between the machine and the PCB
that supports SEND function
Adj/set/operate method N/A (Display only)
Display/adj/set range 0 to 1
0: Not mounted, 1: Mounted
TRIM-CN Display of Trimmer connection state
Lv.1 Details To display the connecting state of Trimmer.
Use case When checking the connection between the machine and Trimmer
Adj/set/operate method N/A (Display only)
Display/adj/set range 0 to 1
0: Not connected, 1: Connected
PDL-FNC1 Display of enabling PDL function (1)
Lv.1 Details To display enabling/disabling state of PDL function in bit row.
When the corresponding bit for each function is 0, the function is
disabled. When the corresponding bit is 1, the function is enabled.
Use case When displaying the available PDL on the machine
Adj/set/operate method N/A (Display only)
Display/adj/set range 0000 0000 0000 0000 to 1111 1111 1111 1111
0: Disabled, 1: Enabled
bit31: BDL
bit30: PS
bit29: PCL
bit28: PDF
bit27: LIPS (LIPS/LX emulation)
bit26: N201 (LIPS/LX emulation)
bit25: I5577 (LIPS/LX emulation)
bit24: ESC/P (LIPS/LX emulation)
bit23: HPGL (LIPS/LX emulation)
bit22: HPCL2 (LIPS/LX emulation)
PDL-FNC2 Display of enabling PDL function (2)
Lv.1 Details To display enabling/disabling state of PDL function in bit row.
When the corresponding bit for each function is 0, the function is
disabled. When the corresponding bit is 1, the function is enabled.
Use case When displaying the available PDL on the machine
Adj/set/operate method N/A (Display only)
Display/adj/set range 0000 0000 0000 0000 to 1111 1111 1111 1111
0: Disabled, 1: Enabled
b15 to b0: Reserved (to be used when PDL is newly added)
HDD Display of HDD model name
Lv.1 Details To display the model name of HDD.
Use case When checking the model name of HDD used on the machine
Adj/set/operate method N/A (Display only)
8-30
8-30