Canon imageRUNNER ADVANCE 8105 Series Service Manual page 959

OPTION
SORTER > OPTION
BLNK-SW Set Saddle Finisher fold position margin
Lv.1 Details To set the margin width of fold position on Saddle Finisher.
Use case When changing the margin width of fold position
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 2
0: Normal, 1: Wider, 2: Entire image (no margin)
Default value 2
MD-SPRTN Restricted operation at Finisher error
Lv.1 Details To set whether to stop the machine when an error occurs at Finisher.
Use case When preferring to run the machine at Finisher error occurrence
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution When "1" is set, staple operation or alignment operation is not
executed. Set "0" normally.
Display/adj/set range 0 to 1
0: Normal, 1: Restricted operation
Default value 0
TRY-OVER Set of fold ppr stack limit: Fin-D1
Lv.1 Details To set the limit of stack capacity for half fold paper and Z-fold paper.
When clearing the limit of stack capacity, paper can be stacked
beyond the maximum stack capacity.
Use case When stacking the paper beyond the maximum stack capacity of the
Tray.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Normal operation, 1: Clearing limit of stack capacity
Default value 0
PUCH-SW High-prdctvty/accurcy punch mod:Fin-D1
Lv.1 Details To switch the high-productivity punch mode or high-accuracy punch
mode of Finisher.
Use case When switching the high-productivity punch mode or high-accuracy
punch mode
Adj/set/operate method Select the item, and then press OK key.
Display/adj/set range 0 to 1
Default value 0
8
Service Mode > SOATER > OPTION
8
Service Mode > SOATER > OPTION
SORTER > OPTION
ALG-IMPR Set Finisher alignment mode: Fin-D1
Lv.1 Details To set the special mode for improving the alignment condition.
Use case When using the special mode for improving the alignment condition
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 20
Appropriate target value 0
Default value 0
BUFF-SW2 Set Finisher buffer operation: Fin-D1
Lv.1 Details To set ON/OFF of buffer operation in the Finisher.
When 1 is set, the alignment condition of the paper delivered from
the lower path may be improved. However, productivity decreases.
Use case When misalignment occurs in the buffer paper delivered from the
lower path
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution When the buffer operation is set to OFF, productivity decreases.
Display/adj/set range 0 to 1
0: ON, 1: OFF
Default value 0
1SHT-SRT Set of 1-sheet Offset&Collate: Fin-D1
Lv.1 Details To set ON/OFF of Offset&Collate for 1-sheet document.
When 1 is set, Offset&Collate for 1-sheet document is enabled, but
the paper is not appropriately stacked.
Use case When preferring to execute 1-sheet Offset&Collate
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
SD-LMTLS Sddl delivery limitless oprtn: Fin-D1
Lv.1 Details To set ON/OFF of the Finisher Saddle Assembly limitless delivery
operation.
When 1 is set, "stack over" does not occur and saddle operation can
be performed continuously, but the stacking condition decreases.
Use case When preferring to perform saddle operation continuously
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution When limitless operation is set to ON, the saddle stacking condition
decreases.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
8-244
8-244