Canon imageRUNNER ADVANCE 8105 Series Service Manual page 620

E Detail
Location Item
Code Code
E017 -0003 -05 Title ETB HP error
Remedy If this error occurs at installation, the ETB Disengage Member
(Transfer Frame Stopper) may be left unremoved. Refer
to the troubleshooting "Remedy to be implemented when
the ETB Disengage Member (Transfer Frame Stopper) is
left unremoved" in the Service Manual, and check whether
the ETB Disengage Member is left unremoved or not and
implement appropriate procedure.
If this error occurs at times other than installation, follow the
following steps to implement check and remedy.
1. Check the connection of the ETB Disengage Sensor
(PS56).
Sensor side: J2101, J3270, PCB side: J343 (Duplex Driver
PCB (PCB4))
2. Check the connection of the Duplex Feed Left Motor (M19).
Motor side: J2107, J3044 (relay), PCB side: J330 (Duplex
Driver PCB (PCB4))
3. Replace the ETB Disengage Sensor (PS56).
4. Replace the Duplex Feed Left Motor (M19).
5. Replace the Duplex Driver PCB (PCB4).
6. Replace the DC Controller PCB (PCB1).
MEMO:
Check if the Disengagement Cam is stained. If
necessary, clean it.
Check if the drive system (gear, Motor, one-way)
is failed. If necessary, replace it.
Check if the link with the Fixing Feed Handle is
failed. If necessary, replace it.
Description Engagement of the ETB was not completed at initialization.
7
Error Code > Error Code > Error Code Details > E000 to E069
Description
7
Error Code > Error Code > Error Code Details > E000 to E069
E Detail
Location Item
Code Code
E020 -0000 -05 Title Developing Assembly toner absent error
Remedy 1. Check the connection of the Developing Toner Sensor
(TS1).
Sensor side: J2133, J3089 (relay), PCB side: J3088 (relay),
J114 (Main Driver PCB (PCB2))
2. Check the connection of the Magnet Roller Clutch (CL5).
Sensor side: J2036, J3124 (relay), J3090 (relay) PCB side:
J3091(relay), J115 (Main Driver PCB (PCB2))
3. Check the connection of the Toner Feed Motor (M28).
Motor side: J2035, J3124 (relay), J3090 (relay) PCB side:
J3091(relay), J115 (Main Driver PCB (PCB2))
4. Check the connection of the Buffer Toner Sensor (TS3).
Sensor side: J2039, J3124 (relay), J3090 (relay) PCB side:
J3091(relay), J115 (Main Driver PCB (PCB2))
5. Replace the Developing Toner Sensor (TS1).
6. Replace the Magnet Roller Clutch (CL5).
7. Replace the Toner Feed Motor (M28).
8. Replace the Buffer Toner Sensor (TS3).
9. Replace the Main Driver PCB (PCB2).
10. Replace the DC Controller PCB (PCB1).
Description Toner in the Developing Assembly was empty for 2 minutes.
E020 -0001 -05 Title Error in Developing Toner Sensor connection detection
Remedy 1. Check the connection of the Developing Toner Sensor
(TS1).
Sensor side: J2133, J3089 (relay), PCB side: J3088 (relay),
J114 (Main Driver PCB (PCB2))
2. Replace the Developing Toner Sensor (TS1).
3. Replace the Main Driver PCB (PCB2).
4. Replace the DC Controller PCB (PCB1).
Description The connection detection port was OFF at power-on.
E020 -0002 -05 Title Error in Buffer Toner Sensor connection detection
Remedy 1. Check the connection of the Buffer Toner Sensor (TS3).
Sensor side: J2039, J3124 (relay), J3090 (relay) PCB side:
J3091(relay), J115 (Main Driver PCB (PCB2))
2. Replace the Buffer Toner Sensor (TS3).
3. Replace the Main Driver PCB (PCB2).
4. Replace the DC Controller PCB (PCB1).
Description The connection detection port was OFF at power-on.
7-6
Description
7-6