Canon imageRUNNER ADVANCE 8105 Series Service Manual page 648

E Detail
Location Item
Code Code
E583 -8002 -05 Title Error in the Tray Auxiliary Guide Motor (Finisher-D1)
Remedy 1. The connector of the Tray Auxiliary Guide Front HP Sensor
(S137) or the Tray Auxiliary Guide Rear HP Sensor (S136)
are disconnected.
2. The connector of the Tray Auxiliary Guide Motor (M120) is
disconnected.
3. The wiring of the Tray Auxiliary Guide Front HP Sensor
(S137) or the Tray Auxiliary Guide Rear HP Sensor (S136)
are faulty.
4. The wiring of the Tray Auxiliary Guide Motor (M120) is
faulty.
5. The Tray Auxiliary Guide Front HP Sensor (S137) is faulty.
6. The Tray Auxiliary Guide Rear HP Sensor (S136) is faulty.
7. The Tray Auxiliary Guide Motor (M120) is faulty.
8. The Finisher Controller PCB is faulty.
Description The Tray Auxiliary Guide Front/Rear HP Sensors does nor
detect the tray auxiliary guide when the Tray Auxiliary Guide
Motor has been driven for 3 seconds.
E584 -0002 -05 Title Error in the Stack Delivery Lower/Shutter Motor (Finisher-D1)
Remedy 1. The connector of the Shutter HP Sensor (S106) or
the Stack Delivery Lower/Shutter Motor (M122) are
disconnected.
2. The wiring of the Shutter HP Sensor (S106) or the Stack
Delivery Lower/Shutter Motor (M122) are faulty.
3. The Shutter HP Sensor (S106) is faulty.
4. The Stack Delivery Lower/Shutter Motor (M122) is faulty.
5. The Finisher Controller PCB is faulty.
Description The Shutter HP Sensor does not detect the shutter when the
Stack Delivery Lower/Shutter Motor has been driven for 3
seconds.
E584 -8001 -05 Title Error in the Stack Delivery Lower/Shutter Motor (Finisher-D1)
Remedy 1. The connector of the Shutter HP Sensor (S106) or
the Stack Delivery Lower/Shutter Motor (M122) are
disconnected.
2. The wiring of the Shutter HP Sensor (S106) or the Stack
Delivery Lower/Shutter Motor (M122) are faulty.
3. The Shutter HP Sensor (S106) is faulty.
4. The Stack Delivery Lower/Shutter Motor (M122) is faulty.
5. The Finisher Controller PCB is faulty.
Description The shutter does not come off the Shutter HP Sensor when
the Stack Delivery Lower/Shutter Motor has been driven for 3
seconds.
7
Error Code > Error Code > Error Code Details > E500 to E5F9
Description
7
Error Code > Error Code > Error Code Details > E500 to E5F9
E Detail
Location Item
Code Code
E584 -8003 -05 Title Error in the Stack Delivery Lower/Shutter Motor (Finisher-D1)
Remedy 1. The connector of the Shutter Close Detection Sensor
(S148) or the Stack Delivery Lower/Shutter Motor (M122)
are disconnected.
2. The wiring of the Shutter Close Detection Sensor (S148) or
the Stack Delivery Lower/Shutter Motor (M122) are faulty.
3. The Shutter Close Detection Sensor (S148) is faulty.
4. The Stack Delivery Lower/Shutter Motor (M122) is faulty.
5. The Finisher Controller PCB is faulty.
Description The shutter does not come off the Shutter Close Detection
Sensor when the Stack Delivery Lower/Shutter Motor has
been driven for 3 seconds.
E584 -8004 -05 Title Error in the Stack Delivery Lower/Shutter Motor (Finisher-D1)
Remedy 1. The connector of the Shutter Close Detection Sensor
(S148) or the Stack Delivery Lower/Shutter Motor (M122)
are disconnected.
2. The wiring of the Shutter Close Detection Sensor (S148) or
the Stack Delivery Lower/Shutter Motor (M122) are faulty.
3. The Shutter Close Detection Sensor (S148) is faulty.
4. The Stack Delivery Lower/Shutter Motor (M122) is faulty.
5. The Finisher Controller PCB is faulty.
Description The Shutter Close Detection Sensor does not detect the
shutter when the Stack Delivery Lower/Shutter Motor has
been driven for 3 seconds.
E590 -8001 -05 Title Error in the Punch Motor (Finisher-D1)
Remedy 1. The connector of the Punch HP Sensor (S104) or the
Punch Motor Clock Sensor (S105) are disconnected.
2. The connector of the Punch Motor (M102) is disconnected.
3. The wiring of the Punch HP Sensor (S104) or the Punch
Motor Clock Sensor (S105) are faulty.
4. The wiring of the Punch Motor (M102) is faulty.
5. The Punch HP Sensor (S104) is faulty.
6. The Punch Motor Clock Sensor (S105) is faulty.
7. The Punch Motor (M102) is faulty.
8. The Puncher Driver PCB (PCB1) is faulty.
9. The Finisher Controller PCB is faulty.
Description 1. During initialization, the Punch HP Sensor does not detect
the Puncher when the Punch Motor has been driven for
500msec. after the Puncher has come off the Punch HP
Sensor.
2. After initialization, the Punch Motor does not return to home
position.
7-34
Description
7-34