Canon imageRUNNER ADVANCE 8105 Series Service Manual page 954

SORTER > ADJUST
TRM-CUT2 Trimming position adjust (large size)
Lv.1 Details To adjust the trimming position of the paper stack larger than A4 size
on Finisher Trimmer.
As the value is incremented by 1, the paper stack stop position
moves by 0.1mm.
+: Toward delivery direction
-: Toward inlet direction
Use case When the trimming position is displaced on the paper stack larger
than A4 size
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -50 to 50
Unit 0.1 mm
Appropriate target value 0
BFF-SFT2 Paper displace amount on buffer
Lv.1 Details To adjust the paper displacement amount on Finisher Buffer
Assembly.
As the value is incremented by 1, the paper position moves by 0.1mm.
Use case When the paper displacement occurs on the 2nd to 3rd sheets of the
2nd sets (B5/A4/LTR) and later
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -50 to 50
Unit 0.1 mm
Default value 0
SDL-STP Adj of Saddle Stitcher staple position
Lv.1 Details To adjust the staple position of Saddle Stitcher.
As the value is incremented by 1, the staple position moves by mm.
Use case When the staple position of the Saddle Stitcher is displaced
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -20 to 20
Unit mm
Default value 0
SDL-FLD Adj of Saddle Stitcher fold position
Lv.1 Details To adjust the fold position of Saddle Stitcher.
As the value is incremented by 1, the fold position moves by mm.
Use case When the fold position of the Saddle Stitcher is displaced
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -20 to 20
Unit mm
Default value 0
8
Service Mode > SOATER > ADJUST
8
Service Mode > SOATER > ADJUST
SORTER > ADJUST
SDL-ALG Adj of Saddle Stitcher alignment width
Lv.1 Details To adjust the alignment width of Saddle Stitcher.
As the value is incremented by 1, the alignment width is increased
by mm.
Use case When the misalignment occurs within a paper stack on the Saddle
Stitcher
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -20 to 20
Unit mm
Default value 0
SDL-RLPT Adj Sddl Sttch Diseng Roll diseng amount
Lv.1 Details To adjust the disengagement amount of Saddle Stitcher
Disengagement Roller.
As the value is incremented by 1, the disengagement amount is
increased by mm.
Use case When the feed failure (with thin paper, etc.) occurs on the Saddle
Stitcher
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -20 to 20
Unit mm
Default value 0
SDL-RLFD Adj Sddl Sttch Diseng Roller feed amount
Lv.1 Details To adjust the feed amount of Saddle Stitcher Disengagement Roller.
As the value is incremented by 1, the feed amount is increased by
mm.
Use case When the feed failure (with thin paper, etc.) occurs on the Saddle
Stitcher
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -20 to 20
Unit mm
Default value 0
SDL-RLHD Adj Sddl Sttch Diseng Roll fold position
Lv.1 Details To adjust the fold position of Saddle Stitcher Disengagement Roller.
As the value is incremented by 1, the fold position moves by mm.
Use case When the feed failure (with thin paper, etc.) occurs on the Saddle
Stitcher
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -20 to 20
Unit mm
Default value 0
8-239
8-239