Canon imageRUNNER ADVANCE 8105 Series Service Manual page 900

COPIER > OPTION >LCNS-TR
ST-HDCLR Installation state display of Data Erase
Lv.2 Details To display installation state of Data Erase (for old model) when
transfer is disabled.
Use case When checking whether Data Erase (for old model) is installed
Adj/set/operate method 1) Select ST-HDCLR.
2) Enter 0, and then press OK key.
When installation has been completed, the transfer license key is
displayed under TR-HDCLR.
When operation finished normally: OK!
Display/adj/set range
Default value 0
TR-HDCLR Transfer license key dis of Data Erase
Lv.2 Details To display transfer license key to use Data Erase (for old model)
when transfer is disabled.
Use case - When replacing HDD
- When replacing the device
Adj/set/operate method 1) Select ST-HDCLR.
2) Enter 0, and then press OK key.
The transfer license key is displayed under TR-HDCLR.
Caution This mode is enabled when there is "3DES+USH-H" Board.
Display/adj/set range 24 digits
ST-BRDIM Install state dis: PCL Barcode Printing
Lv.2 Details To display installation state of Barcode Printing for PCL when transfer
is disabled.
Use case When checking whether Barcode Printing for PCL is installed
Adj/set/operate method 1) Select ST-BRDIM.
2) Enter 0, and then press OK key.
When installation has been completed, the transfer license key is
displayed under TR-BRDIM.
When operation finished normally: OK!
Display/adj/set range
Default value 0
TR-BRDIM Trns lcns key dis: PCL Barcode Printing
Lv.2 Details To display transfer license key to use Barcode Printing for PCL when
transfer is disabled.
Use case - When replacing HDD
- When replacing the device
Adj/set/operate method 1) Select ST-BRDIM.
2) Enter 0, and then press OK key.
The transfer license key is displayed under TR-BRDIM.
Display/adj/set range 24 digits
8
Service Mode > COPIER > OPTION > LCNS-TR
8
Service Mode > COPIER > OPTION > LCNS-TR
COPIER > OPTION >LCNS-TR
ST-VNC Install state dis of Remote Oprtr Soft
Lv.2 Details To display installation state of Remote Operators Software when
transfer is disabled.
Use case When checking whether Remote Operators Software is installed
Adj/set/operate method 1) Select ST-VNC.
2) Enter 0, and then press OK key.
When installation has been completed, the transfer license key is
displayed under TR-VNC.
When operation finished normally: OK!
Display/adj/set range
Default value 0
TR-VNC Trns lcns dis of Remote Operators Soft
Lv.2 Details To display transfer license key to use Remote Operators Software
when transfer is disabled.
Use case - When replacing HDD
- When replacing the device
Adj/set/operate method 1) Select ST-VNC.
2) Enter 0, and then press OK key.
The transfer license key is displayed under TR-VNC.
Display/adj/set range 24 digits
ST-WEB Install state dis of Web Access Software
Lv.2 Details To display installation state of Web Access Software when transfer is
disabled.
Use case When checking whether Web Access Software is installed
Adj/set/operate method 1) Select ST-WEB.
2) Enter 0, and then press OK key.
When installation has been completed, the transfer license key is
displayed under TR-WEB.
When operation finished normally: OK!
Display/adj/set range
Default value 0
TR-WEB Trns license key dis of Web Access Soft
Lv.2 Details To display transfer license key to use Web Access Software when
transfer is disabled.
Use case - When replacing HDD
- When replacing the device
Adj/set/operate method 1) Select ST-WEB.
2) Enter 0, and then press OK key.
The transfer license key is displayed under TR-WEB.
Display/adj/set range 24 digits
8-185
8-185