Canon imageRUNNER ADVANCE 8105 Series Service Manual page 794

■
CCD
COPIER > ADJUST > CCD
W-PLT-X White level data(X) entry of white plate
Lv.1 Details When replacing the Reader Controller PCB/clearing RAM data, enter
the value of service label. When replacing the Copyboard Glass,
enter the value of barcode label which is affixed on the glass.
Use case - When replacing the Reader Controller PCB/clearing RAM data
- When replacing the Copyboard Glass
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Do not use this at the normal service.
Display/adj/set range 7500 to 9999
Default value 8271
Related service mode COPIER > ADJUST > CCD > W-PLT-Y, W-PLT-Z
W-PLT-Y White level data(Y) entry of white plate
Lv.1 Details When replacing the Reader Controller PCB/clearing RAM data, enter
the value of service label. When replacing the Copyboard Glass,
enter the value of barcode label which is affixed on the glass.
Use case - When replacing the Reader Controller PCB/clearing RAM data
- When replacing the Copyboard Glass
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution After the setting value is changed, write the changed value in the
service label.
Display/adj/set range 7500 to 9999
Default value 8735
Related service mode COPIER > ADJUST > CCD > W-PLT-X, W-PLT-Z
W-PLT-Z White level data(Z) entry of white plate
Lv.1 Details When replacing the Reader Controller PCB/clearing RAM data, enter
the value of service label. When replacing the Copyboard Glass,
enter the value of barcode label which is affixed on the glass.
Use case - When replacing the Reader Controller PCB/clearing RAM data
- When replacing the Copyboard Glass
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution After the setting value is changed, write the changed value in the
service label.
Display/adj/set range 7500 to 9999
Default value 9418
Related service mode COPIER > ADJUST > CCD > W-PLT-X, W-PLT-Y
8
Service Mode > COPIER > ADJUST > CCD
8
Service Mode > COPIER > ADJUST > CCD
COPIER > ADJUST > CCD
SH-TRGT Shading target value (B&W) [Copyboard]
Lv.1 Details To set the B&W shading target value in copyboard reading mode.
Use case - When replacing the Reader Controller PCB/clearing RAM data
- When replacing the Scanner Unit
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution After the setting value is changed, write the changed value in the
service label.
Display/adj/set range 700 to 1400
Default value 1126
100-RG Img Sensr RG color displace crrct VL:Frt
Lv.1 Details To correct the color displacement (R and G lines) in vertical scanning
direction due to the Scanner Unit (paper front).
When replacing the Reader Controller PCB/clearing RAM data, enter
the value of service label.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Caution After the setting value is changed, write the changed value in the
service label.
Display/adj/set range -256 to 256
Unit 0.001 line
Default value 0
100-GB Img Sensr GB color displace crrct VL:Frt
Lv.1 Details To correct the color displacement (G and B lines) in vertical scanning
direction due to the Scanner Unit (paper front).
When replacing the Reader Controller PCB/clearing RAM data, enter
the value of service label.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
2) Turn OFF/ON the main power switch.
Caution After the setting value is changed, write the changed value in the
service label.
Display/adj/set range -256 to 256
Unit 0.001 line
Default value 0
8-79
8-79