Canon imageRUNNER ADVANCE 8105 Series Service Manual page 802

COPIER > ADJUST > CCD
MTF-M11 MTF value 11 setting: horz scan [Back]
Setting value for MTF filter coefficient calculation.
Lv.1 Details
Enter the value of service label on the Reader.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF-M12 MTF value 12 setting: horz scan [Back]
Setting value for MTF filter coefficient calculation.
Lv.1 Details
Enter the value of service label on the Reader.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF-S10 MTF value 10 setting: vert scan [Back]
Setting value for MTF filter coefficient calculation.
Lv.1 Details
Enter the value of service label on the Reader.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF-S11 MTF value 11 setting: vert scan [Back]
Setting value for MTF filter coefficient calculation.
Lv.1 Details
Enter the value of service label on the Reader.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF-S12 MTF value 12 setting: vert scan [Back]
Setting value for MTF filter coefficient calculation.
Lv.1 Details
Enter the value of service label on the Reader.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
8
Service Mode > COPIER > ADJUST > CCD
8
Service Mode > COPIER > ADJUST > CCD
COPIER > ADJUST > CCD
DFCH2K2 Complex chart No.2 data (B&W) [Front]
Lv.1 Details To derive the front/back side linearity, set the B&W data (for paper
front) of No.2 image in DADF complex chart.
Enter the value of service label on the Reader.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 1 to 2550
Default value 2000
DFCH2K10 Complex chart No.10 data (B&W) [Front]
Lv.1 Details To derive the front/back side linearity, set the B&W data (for paper
front) of No.10 image in DADF complex chart.
Enter the value of service label on the Reader.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 2550
Default value 0
DFCH-K2 Complex chart No.2 data (B&W) [Back]
Lv.1 Details To derive the front/back side linearity, set the B&W data (for paper
back) of No.2 image in DADF complex chart.
Enter the value of service label on the Reader.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 1 to 2550
Default value 2000
Related service mode COPIER> ADJUST> CCD> DFCH-R2, DFCH-R10, DFCH-B2,
DFCH-B10, DFCH-G2, DFCH-G10, DFCH-K10
COPIER> FUNCTION> CCD> DF-LNR
DFCH-K10 Complex chart No.10 data (B&W) [Back]
Lv.1 Details To derive the front/back side linearity, set the B&W data (for paper
back) of No.10 image in DADF complex chart.
Enter the value of service label on the Reader.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 2550
Default value 0
Related service mode COPIER> ADJUST> CCD> DFCH-R2, DFCH-R10, DFCH-B2,
DFCH-B10, DFCH-G2, DFCH-G10, DFCH-K2
COPIER> FUNCTION> CCD> DF-LNR
8-87
8-87