Canon imageRUNNER ADVANCE 8105 Series Service Manual page 690

E Detail
Location Item
Code Code
E711 -0040 -05 Title IPC communication error (serial error)
Remedy 1. Check the cable connection.
Check the connection between DCON side (J462) and
Finisher Lattice side (J9043)
Finisher Cable
2. Replace the DC Controller PCB.
Description Communication between the host machine and the Finisher
was lost.
E713 -0001 -05 Title Finisher IPC communication error (retransmission request
reception error)
Remedy 1. Check the cable connection of the Finisher.
DC Controller side: J462, Finisher Lattice side: J9043
2. Replace the Finisher Controller PCB.
Description Communication between the host machine and the Finisher
was lost.
E713 -0002 -05 Title Finisher IPC communication error (reception timeout)
Remedy 1. Check the cable connection of the Finisher.
DC Controller side: J462, Finisher Lattice side: J9043
2. Replace the Finisher Controller PCB.
Description Communication between the host machine and the Finisher
was lost.
E713 -0004 -05 Title Finisher IPC communication error (checksum error)
Remedy 1. Check the cable connection of the Finisher.
DC Controller side: J462, Finisher Lattice side: J9043
2. Replace the Finisher Controller PCB.
Description Communication between the host machine and the Finisher
was lost.
E713 -0020 -05 Title Finisher IPC communication error (recovery error)
Remedy 1. Check the cable connection of the Finisher.
DC Controller side: J462, Finisher Lattice side: J9043
2. Replace the Finisher Controller PCB.
Description Communication between the host machine and the Finisher
was lost.
E713 -0040 -05 Title Finisher IPC communication error (serial error)
Remedy 1. Check the cable connection of the Finisher.
DC Controller side: J462, Finisher Lattice side: J9043
2. Replace the Finisher Controller PCB.
Description Communication between the host machine and the Finisher
was lost.
7
Error Code > Error Code > Error Code Details > E710 to E753
Description
7
Error Code > Error Code > Error Code Details > E710 to E753
E Detail
Location Item
Code Code
E717 -0001 -00 Title Communication error with the NE Controller
Remedy Check the cable, and then go through the following to clear
the error: Service Mode > COPIER > FUNCTION > CLEAR >
ERR.
Description Error when the NE Controller is started.
The NE Controller which was connected before turning OFF
the power is not connected at power-on.
E717 -0002 -00 Title Communication error with the NE Controller
Remedy Check the cable, and then go through the following to clear
the error: Service Mode > COPIER > FUNCTION > CLEAR >
ERR.
Description IPC error at NE Controller operation.
Open circuit of IPC, unable to recover the IPC communication.
E719 -0001 -00 Title Error in coin manager
Remedy Check the cable, and then go through the following to clear
the error: Service Mode > COPIER > FUNCTION > CLEAR >
ERR.
Description Error when the coin manager is started.
The coin manager which was connected before turning OFF
the power is not connected at power-on.
E719 -0002 -00 Title Error in coin manager
Remedy Check the cable, and then go through the following to clear
the error: Service Mode > COPIER > FUNCTION > CLEAR >
ERR.
Description IPC error at coin manager operation.
Open circuit of IPC, unable to recover the IPC communication.
When open circuit of the pickup/delivery signal cable is
detected.
Invalid connection is detected.
E719 -0003 -00 Title Error in coin manager
Remedy Check the cable, and then go through the following to clear
the error: Service Mode > COPIER > FUNCTION > CLEAR >
ERR.
Description Communication error with the coin manager occurs during
unit price acquisition at startup.
E719 -0011 -00 Title Error when the Card Reader is started
Remedy Check the cable, and then go through the following to clear
the error: Service Mode > COPIER > FUNCTION > CLEAR >
ERR.
Description The Card Reader which was connected before turning OFF
the power is not connected at power-on.
7-76
Description
7-76