Canon imageRUNNER ADVANCE 8105 Series Service Manual page 870

COPIER > OPTION > FEED-SW
DK1-TURN ON/OFF of R-Deck Pckup Rol little rotn
Lv.1 Details To set whether to rotate the Right Deck Pickup Roller a little after
completion of job or at the time of warm-up rotation.
If the Pickup Deck has not been used for a long time, a part of the
Separation Roller engaged with the Pickup Roller becomes worn and
the roller stops rotation. As a result of that, jam may occur. When 1
is set, the Pickup Roller rotates 75mm after completion of job so that
wear of the Separation Roller can be reduced.
As the usage is extended or at the operation performed first time for
the day in a low temperature environment, the Separation Roller is
not rotated in response to rotation of the Pickup Roller. As a result of
that, jam may occur. When 2 is set, the Pickup Roller rotates 75mm
at warm-up rotation.
Use case When pickup jam occurs with the following conditions
- Pickup Deck has not been used for a long time
- The usage is extended
- At the operation performed first time for the day in a low
temperature environment
Caution When ON is set, papers sticking out of the Receptacle may get stuck
at the time of opening and closing the deck.
Display/adj/set range 0 to 3
0: OFF, 1: ON after a job, 2: ON at warm-up rotation, 3: ON after a
job and at warm-up rotation
Default value 0
Related service mode COPIER> OPTION> FEED-SW> DK2-TURN, DK3-TURN, DK4-
TURN, DK5-TURN
8
Service Mode > COPIER > OPTION > FEED-SW
8
Service Mode > COPIER > OPTION > FEED-SW
COPIER > OPTION > FEED-SW
DK5-TURN ON/OFF of OP-Deck Pckup Rol little rotn
Lv.1 Details To set whether to rotate the Option Deck Pickup Roller a little after
completion of job or at the time of warm-up rotation.
If the Pickup Deck has not been used for a long time, a part of the
Separation Roller engaged with the Pickup Roller becomes worn and
the roller stops rotation. As a result of that, jam may occur. When 1
is set, the Pickup Roller rotates 75mm after completion of job so that
wear of the Separation Roller can be reduced.
As the usage is extended or at the operation performed first time for
the day in a low temperature environment, the Separation Roller is
not rotated in response to rotation of the Pickup Roller. As a result of
that, jam may occur. When 2 is set, the Pickup Roller rotates 75mm
at warm-up rotation.
Use case When pickup jam occurs with the following conditions
- Pickup Deck has not been used for a long time
- The usage is extended
- At the operation performed first time for the day in a low
temperature environment
Caution When ON is set, papers sticking out of the Receptacle may get stuck
at the time of opening and closing the deck.
Display/adj/set range 0 to 3
0: OFF, 1: ON after a job, 2: ON at warm-up rotation, 3: ON after a
job and at warm-up rotation
Default value 0
Related service mode COPIER> OPTION> FEED-SW> DK1-TURN, DK2-TURN, DK3-
TURN, DK4-TURN
DK1-AIR ON/OFF of PDF Deck Lite air assist
Lv.1 Details To set ON/OFF of the POD Deck Lite air assist.
In the initial settings, the air assist is OFF for plain paper, and ON for
coated paper and heavy paper.
When a jam or double feed error frequently occurs with plain paper,
etc., set the value to 1. When the transfer failure occurs with coated
paper, heavy paper, etc., set the value to 2.
Use case - When a jam or double feed error frequently occurs with plain paper
- When transfer failure occurs with coated paper and heavy paper
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 2
0: Initial setting, 1: ON, 2: OFF
Default value 0
8-155
8-155