Canon imageRUNNER ADVANCE 8105 Series Service Manual page 958

SORTER > FUNCTION
VR2-LTRR Adj Lower Tray width vol (LTRR):Inserter
Lv.1 Details To adjust the paper minimum width (LTRR) of Inserter Lower Tray
automatically.
Use case When the size mismatch jam is incorrectly detected at the pickup
from Inserter Lower Tray
Adj/set/operate method 1) Set the LTRR paper on the Inserter Lower Tray and align it with
the width of Slide Guide.
2) Select the item, and then press OK key.
VR2-LTR Adj Lower Tray width vol (LTR): Inserter
Lv.1 Details To adjust the paper maximum width (LTR) of Inserter Lower Tray
automatically.
Use case When the size mismatch jam is incorrectly detected at the pickup
from Inserter Lower Tray
Adj/set/operate method 1) Set the LTR paper on the Inserter Lower Tray and align it with the
width of Slide Guide.
2) Select the item, and then press OK key.
FIN-CON Controller PCB RAM clear
Lv.1 Details To execute the RAM clear of Finisher Controller PCB to delete all the
adjustment contents and counter information.
Adj/set/operate method 1) Select the item, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution - Output the service mode setting values by P-PRINT before
execution. After execution, enter necessary setting values.
- The RAM data is cleared after the main power switch is turned
OFF/ON.
Related service mode COPIER> FUNCTION> MISC-P> P-PRINT
PF-CON Controller PCB RAM clear: PFU
Lv.1 Details To execute the RAM clear of Inserter/Folder Controller PCB on
Paper Folding Unit to delete all the adjustment contents and counter
information.
Adj/set/operate method Select the item, and then press OK key.
PF-SENS1 Adj Slowdown Timing Sensor output: PFU
Lv.1 Details To adjust the output of Slowdown Timing Sensor on Paper Folding
Unit automatically.
Use case - When replacing the Slowdown Timing Sensor
- When replacing the Controller PCB
Adj/set/operate method Select the item, and then press OK key.
PF-SENS2 Adj Release Timing Sensor output: PFU
Lv.1 Details To adjust the output of Release Timing Sensor on Paper Folding Unit
automatically.
Use case - When replacing the Release Timing Sensor
- When replacing the Controller PCB
Adj/set/operate method Select the item, and then press OK key.
8
Service Mode > SOATER > FUNCTION
8
Service Mode > SOATER > FUNCTION
SORTER > FUNCTION
PF-SENS3 Adj Fold Position Sensor output: PFU
Lv.1 Details To adjust the output of Fold Position Sensor on Paper Folding Unit
automatically.
Use case - When replacing the Fold Position Sensor
- When replacing the Controller PCB
Adj/set/operate method Select the item, and then press OK key.
PF-SENS4 Adj Upper Stopper Path Sensor output:PFU
Lv.1 Details To adjust the output of Upper Stopper Path Sensor on Paper Folding
Unit automatically.
Use case - When replacing the Upper Stopper Path Sensor
- When replacing the Controller PCB
Adj/set/operate method Select the item, and then press OK key.
TRM-SENS Adjust of Trimmer Dust Sensor output
Lv.1 Details To adjust the output of Saddle Dust Sensor on Saddle Unit
automatically.
Use case - When installing the Trimmer
- When replacing the Trimmer Dust Sensor
- When replacing the Saddle Controller PCB
Adj/set/operate method Select the item, and then press OK key.
IS-CON DC Controller PCB RAM clear: Inserter
Lv.1 Details To execute the RAM clear of Inserter DC Controller PCB to delete all
the adjustment contents and counter information.
Adj/set/operate method Select the item, and then press OK key.
8-243
T-8-93
8-243