Canon imageRUNNER ADVANCE 8105 Series Service Manual page 877

COPIER > OPTION > NETWORK
DNSTRANS Setting of DNS transfer priority
Lv.1 Details To set priority order of the protocol (IPv4/IPv6) to be used for DNS
query.
In the case of using both IPv6 and IPv4 while the DNS server
supports IPv4, it takes time because of timeout when executing
DNS query with priority on IPv6. Giving priority on query by IPv4 can
shorten the time.
Use case When it takes time to execute DNS query with priority on IPv6
because the DNS server supports IPv4
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: IPv4, 1: IPv6
Default value 1
PROXYRES Setting of proxy response to Windows
Lv.2 Details To set whether to provide proxy response or return the device status
when an inquiry is received via Windows while the device is in sleep
mode.
Use case When executing status response for query from Windows correctly
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: No proxy response, 1: Proxy response
Default value 1
WOLTRANS Setting of sleep recovery protocol
Lv.1 Details To set the protocol for recovery from sleep mode according to the
value of WOL (Wake On LAN) trans.
Reception of a specific network packet is one of the requirements for
the device to recover from sleep mode.
When the number of network protocols supported by the device
increases, the types of network packets which activate recovery from
sleep mode vary. However, there is a possibility that the existing
network protocol is actually used.
Select the type of network packet which activates recovery from
sleep mode according to the environment where the device is used.
Use case When selecting protocol for sleep recovery
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 1 to 3
1: WSD and SNMP, 2: WSD and CPCA, 3: CPCA and SNMP
Default value 1
8
Service Mode > COPIER > OPTION > NETWORK
8
Service Mode > COPIER > OPTION > NETWORK
COPIER > OPTION > NETWORK
802XTOUT Set of IEEE802.1X authentication timeout
Lv.1 Details To set timeout value for IEEE802.1X authentication.
If the device executes 802.1X authentication, change the wait time
for response from the authentication server.
Use case When response from the authentication server is slow/fast
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 10 to 120
Unit second
Default value 30
IKERETRY Setting of IKE retry times
Lv.1 Details To set the number of retries in the case of no response from the
communication target at the time of IKE packet transmission.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 3
Default value 2
Supplement/memo IKE: Internet Key Exchange
SPDALDEL Initialization of SPD value
Lv.2 Details To initialize all the SPD values that are under management.
SPD values can be initialized without clearing SRAM.
Use case At the time of SPD value mismatch when IPSec Board is added
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
Supplement/memo SPD: Database that manages SA (Security Association).
SPD value is managed when IPSec Board is used. Normally, SRAM
needs to be cleared in the case of mismatch in SPD value.
ON/OFF of Network Configurator function
NCONF-SW
To set ON/OFF of Network Configurator function.
Lv.1 Details
If the user does not use the function, select OFF to prevent remote
attack through network.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 1
Network Configurator function is a function to be used for
Supplement/memo
communication with NetSpot Device Installer, etc., and the network
setting can be changed from the remote.
8-162
8-162