Canon imageRUNNER ADVANCE 8105 Series Service Manual page 651

Hide thumbs Also See for imageRUNNER ADVANCE 8105 Series:
Table of Contents

Advertisement

E
Detail
Location
Item
Code
Code
E5BA -8012
-05
Title
Error in the Rear Estrangement Motor (Finisher-D1)
Remedy
1. The connector of the Rear Estrangement Motor HP Sensor
(S104) or the Rear Estrangement Motor (M104) are
disconnected.
2. The wiring of the Rear Estrangement Motor HP Sensor
(S104) or the Rear Estrangement Motor (M104) are faulty.
3. The Rear Estrangement Motor HP Sensor (S104) is faulty.
4. The Rear Estrangement Motor (M104) is faulty.
5. The Trimmer Controller PCB (PCB1) is faulty.
Description The Rear Estrangement Motor HP Sensor does not turn OFF
when the Rear Estrangement Motor has been driven for 537
msec.
E5BB -8001
-05
Title
Error in the Waste Paper Full Sensor (Finisher-D1)
Remedy
1. The connector of the Waste Paper Full Sensor (emitting/
receiving) (S011) is disconnected.
2. The wire of the Waste Paper Full Sensor (emitting/
receiving) (S011) is faulty.
3. The Waste Paper Full Sensor (emitting/receiving) (S011) is
faulty.
4. The Trimmer Controller PCB (PCB1) is faulty.
Description The A/D input value does not enter into the D/A output upper
limit of the Waste Paper Full Sensor.
E5BB -8002
-05
Title
Error in the Waste Paper Full Sensor (Finisher-D1)
Remedy
1. The connector of the Waste Paper Full Sensor (emitting/
receiving) (S011) is disconnected.
2. The wire of the Waste Paper Full Sensor (emitting/
receiving) (S011) is faulty.
3. The Waste Paper Full Sensor (emitting/receiving) (S011) is
faulty.
4. The Trimmer Controller PCB (PCB1) is faulty.
Description The A/D input value does not enter into the D/A output lower
limit of the Waste Paper Full Sensor.
7
Error Code > Error Code > Error Code Details > E500 to E5F9
Description
7
Error Code > Error Code > Error Code Details > E500 to E5F9
E
Detail
Location
Item
Code
Code
E5F0 -8001
-05
Title
Error in the Saddle Lead Edge Stopper Motor (Finisher-D1)
Remedy
1. The connector of the Saddle Lead Edge Stopper HP
Sensor (S205) or the Saddle Lead Edge Stopper Motor
(M203) are disconnected.
2. The wiring of the Saddle Lead Edge Stopper HP Sensor
(S205) or the Saddle Lead Edge Stopper Motor (M203) are
faulty.
3. The Saddle Lead Edge Stopper HP Sensor (S205) is faulty.
4. The Saddle Lead Edge Stopper Motor (M203) is faulty.
5. The Saddle Stitcher Controller PCB is faulty.
6. The Finisher Controller PCB is faulty.
Description The Saddle Lead Edge Stopper HP Sensor does not detect
the Saddle lead edge stopper when the Saddle lead edge
stopper has been moved for 182 mm by Saddle Lead Edge
Stopper Motor.
E5F0 -8002
-05
Title
Error in the Saddle Lead Edge Stopper Motor (Finisher-D1)
Remedy
1. The connector of the Saddle Lead Edge Stopper HP
Sensor (S205) or the Saddle Lead Edge Stopper Motor
(M203) are disconnected.
2. The wiring of the Saddle Lead Edge Stopper HP Sensor
(S205) or the Saddle Lead Edge Stopper Motor (M203) are
faulty.
3. The Saddle Lead Edge Stopper HP Sensor (S205) is faulty.
4. The Saddle Lead Edge Stopper Motor (M203) is faulty.
5. The Saddle Stitcher Controller PCB is faulty.
6. The Finisher Controller PCB is faulty.
Description The Saddle lead edge stopper does not come off the Saddle
Lead Edge Stopper HP Sensor when the Saddle Lead Edge
Stopper Motor has been driven for 50 pulses.
E5F1 -8001
-05
Title
Saddle folder/feeder clock error (Finisher-D1)
Remedy
1. The connector of the Saddle Folder/Feeder Motor Sensor
(S214) or the Saddle Folder/Feeder Motor (M206) are
disconnected.
2. The wiring of the Saddle Folder/Feeder Motor Sensor
(S214) or the Saddle Folder/Feeder Motor (M206) are
faulty.
3. The Saddle Folder/Feeder Motor Sensor (S214) is faulty.
4. The Saddle Folder/Feeder Motor (M206) is faulty.
5. The Saddle Stitcher Controller PCB is faulty.
6. The Finisher Controller PCB is faulty.
Description The drive speed of the Saddle Folder/Feeder Motor is less
than 5 mm/sec.
7-37
Description
7-37

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents