Canon imageRUNNER ADVANCE 8105 Series Service Manual page 619

E Detail
Location Item
Code Code
E013 -0002 -05 Title Error in Waste Toner Feed Screw Lock detection
Remedy 1. Check the Waste Toner Container and the Waste Toner
Container Pipe.
If toner overflowed from the Waste Toner Container clogs
the outlet of the Waste Toner Pipe, remove the clogged
toner.
After removing it, check that the screw can be seen from
the outlet of the pipe.
2. Check the connection of the Waste Toner Lock Detection
Switch (SW5) and the Main Driver PCB (PCB2).
3. Check the connection of the Main Driver PCB (PCB2) and
the DC Controller PCB (PCB1).
Main Controller side: J3050, DC Controller side: J103
4. Replace the Waste Toner Lock Detection Switch (SW5).
5. Replace the Waste Toner Feed Unit.
6. Replace the Main Driver PCB (PCB2).
7. Replace the DC Controller PCB (PCB1). (When the error
is still displayed after replacing the Waste Toner Feed Unit
and the Main Driver PCB (PCB2).)
Description The Waste Toner Lock Detection Switch detects locked
state 3 times for 200 msec while the Developing Assembly is
driven.
E014 -0001 -05 Title Fixing Motor error
Remedy 1. Check the gear of the Fixing Drive Unit. -> Replace the
gear.
2. Replace the Fixing Motor (M3).
3. Check the connection drawer between the Fixing Assembly
and the host machine.
4. Replace the Main Driver PCB (PCB2).
Description Lock error of the Fixing Motor (M3).
7
Error Code > Error Code > Error Code Details > E000 to E069
Description
7
Error Code > Error Code > Error Code Details > E000 to E069
E Detail
Location Item
Code Code
E017 -0001 -05 Title ETB disengagement error
Remedy 1. Check the connection of the ETB Disengage Sensor
(PS56).
Sensor side: J2101, J3270, PCB side: J343 (Duplex Driver
PCB (PCB4))
2. Check the connection of the Duplex Feed Left Motor (M19).
Motor side: J2107, J3044 (relay), PCB side: J330 (Duplex
Driver PCB (PCB4))
3. Replace the ETB Disengage Sensor (PS56).
4. Replace the Duplex Feed Left Motor (M19).
5. Replace the Duplex Driver PCB (PCB4).
6. Replace the DC Controller PCB (PCB1).
MEMO:
Check if the Disengagement Cam is stained. If
necessary, clean it.
Check if the drive system (gear, Motor, one-way)
is failed. If necessary, replace it.
Check if the link with the Fixing Feed Handle is
failed. If necessary, replace it.
Description Disengagement of the ETB is not completed within the
specified period of time.
E017 -0002 -05 Title ETB engagement error
Remedy 1. Check the connection of the ETB Disengage Sensor
(PS55).
Sensor side: J2100, J3270, PCB side: J343 (Duplex Driver
PCB (PCB4))
2. Check the connection of the Duplex Feed Left Motor (M19).
Motor side: J2107, J3044 (relay), PCB side: J330 (Duplex
Driver PCB (PCB4))
3. Replace the ETB Engage Sensor (PS55).
4. Replace the Duplex Feed Left Motor (M19).
5. Replace the Duplex Driver PCB (PCB4).
6. Replace the DC Controller PCB (PCB1).
MEMO:
Check if the Disengagement Cam is stained. If
necessary, clean it.
Check if the drive system (gear, Motor, one-way)
is failed. If necessary, replace it.
Check if the link with the Fixing Feed Handle is
failed. If necessary, replace it.
Description Engagement of the ETB is not completed within the specified
period of time.
7-5
Description
7-5