E100 To E197 - Canon imageRUNNER ADVANCE 8105 Series Service Manual

■

E100 to E197

E Detail
Location Item
Code Code
E100 -11xx -05 Title BD unlock error
Remedy 1. Check if the door is opened. Close the door.
2. Check the connection between the DC Controller PCB
(PCB1) and the Laser Driver PCB (PCB35).
DC Controller side: J471, J472, Laser Driver side: J5100,
J5101, Relay Harness connection to Polygon Motor and
BD PCB: J3011
3. Replace the Laser Scanner Unit.
4. Replace the Laser Driver PCB (PCB35).
5. Replace the DC Controller PCB (PCB1).
MEMO:
When condensation occurs inside of the machine
or the Laser Scanner Unit, this error also occurs.
When condensation occurs, leave the machine or
the unit as it is until condensation disappears. (Use
the machine or the unit in an environment where
condensation does not occur.)
Description Locked state was not detected within the specified period of
time at start-up.
E100 -12xx -05 Title BD unlock error
Remedy 1. Check if the door is opened. Close the door.
2. Check the connection between the DC Controller PCB
(PCB1) and the Laser Driver PCB (PCB35).
DC Controller side: J471, J472, Laser Driver side: J5100,
J5101, Relay Harness connection to Polygon Motor and
BD PCB: J3011
3. Replace the Laser Scanner Unit.
4. Replace the Laser Driver PCB (PCB35).
5. Replace the DC Controller PCB (PCB1).
MEMO:
When condensation occurs inside of the machine
or the Laser Scanner Unit, this error also occurs.
When condensation occurs, leave the machine or
the unit as it is until condensation disappears. (Use
the machine or the unit in an environment where
condensation does not occur.)
Description After the BD range was specified, lock was unlocked for 1
second or longer.
7
Error Code > Error Code > Error Code Details > E100 to E197
Description
7
Error Code > Error Code > Error Code Details > E100 to E197
E Detail
Location Item
Code Code
E100 -13xx -05 Title Polygon Motor BD unlock error (Laser diode is not lit up/
failure of the BD PCB/power supply error, or condensation)
Remedy 1. Check if the door is opened. Close the door.
2. Check the connection between the DC Controller PCB
(PCB1) and the Laser Driver PCB (PCB35).
DC Controller side: J471, J472, Laser Driver side: J5100,
J5101, Relay Harness connection to Polygon Motor and
BD PCB: J3011
3. Replace the Laser Scanner Unit.
4. Replace the Laser Driver PCB (PCB35).
5. Replace the DC Controller PCB (PCB1).
MEMO:
When condensation occurs inside of the machine
or the Laser Scanner Unit, this error also occurs.
When condensation occurs, leave the machine or
the unit as it is until condensation disappears. (Use
the machine or the unit in an environment where
condensation does not occur.)
Description During the Polygon speed change, lock was unlocked for 1
second or longer. (Laser diode is not lit up/failure of the BD
PCB/power supply error, or condensation)
E100 -FFFF -05 Title Polygon Motor BD unlock error
Remedy 1. Check if the door is opened. Close the door.
2. Check the connector connection, open circuit, and the
caught cable of the DC Controller PCB (PCB1) and the
Laser Driver PCB (PCB35).
DC Controller side: J471, J472, Laser Driver side: J5100,
J5101, Relay Harness connection to Polygon Motor (M44)
and BD Sensor: J3011
3. Replace the Laser Scanner Unit.
4. Replace the Laser Driver PCB (PCB35).
5. Replace the DC Controller PCB (PCB1).
Description Failed to get the Detailed Code (communication error, power
supply error, PCB failure, etc.).
7-13
Description
7-13