Canon imageRUNNER ADVANCE 8105 Series Service Manual page 832

■
PART-CHK
COPIER > FUNCTION > PART-CHK
Specification of operation Clutch
CL
Lv.1 Details To specify the Clutch to operate.
Use case When replacing the Clutch/checking the operation
Adj/set/operate method Enter the value, and then press OK key.
Display/adj/set range 1 to 6
1: Developing Clutch (CL1)
2: Magnet Roller Clutch (CL5)
3 to 6: Not used
Default value 0
Related service mode COPIER> FUNCTION> PART-CHK> CL-ON
CL-ON Operation check of Clutch
To start operation check of the Clutch specified by CL.
Lv.1 Details
The operation stops after "ON for 0.5 sec" => "OFF for 10 sec" => "ON
for 0.5 sec" => "OFF for 10 sec" => "ON for 0.5 sec".
Use case When replacing the Clutch/checking the operation
Adj/set/operate method Select the item, and then press OK key.
During operation: ACTIVE, When operation finished normally: OK!
Display/adj/set range
Default value 0
Required time Approx. 22 seconds
Related service mode COPIER> FUNCTION> PART-CHK> CL
Specification of operation Motor
MTR
Lv.1 Details To specify the Motor to operate.
Use case When replacing the Motor/checking the operation
Adj/set/operate method Enter the value, and then press OK key.
Caution Be sure to remove the Toner Container before Toner Supply Motor
(M10) is activated. If it remains to be installed, toner is supplied.
Display/adj/set range 1 to 16
1: Toner Supply Motor (M10)
2: Toner Feed Motor (M28)
3: Delivery Motor (M13)
4: Reverse Motor (M14)
5: Side Registration Motor (M16)
6: Duplex Feed Right Motor (M18)
7: Duplex Feed Left Motor (M19)
8: Vertical Path Upper Motor (M26)
9: Vertical Path Lower Motor (M27)
10: Vertical Path Middle Motor (M31)
11: Duplex Feed Merging Motor (M32)
12: Multi-purposeTray Registration Front Motor (M33)
13: Registration Motor (M34)
14: ETB Motor (M43)
15 to 16: Not used
Default value 1
Related service mode COPIER> FUNCTION> PART-CHK> MTR-ON
8
Service Mode > COPIER > FUNCTION > PART-CHK
8
Service Mode > COPIER > FUNCTION > PART-CHK
COPIER > FUNCTION > PART-CHK
MTR-ON Operation check of Motor
To start operation check of the Motor specified by MTR.
Lv.1 Details
The operation automatically stops after operation of 20 seconds.
Use case When replacing the Motor/checking the operation
Adj/set/operate method Select the item, and then press OK key.
Caution Be sure to remove the Toner Container before Toner Supply Motor
(M10) is activated. If it remains to be installed, toner is supplied.
During operation: ACTIVE, When operation finished normally: OK!
Display/adj/set range
Required time 1 minute
Related service mode COPIER> FUNCTION> PART-CHK> MTR
Specification of operation Solenoid
SL
Lv.1 Details To specify the Solenoid to operate.
Use case When replacing the Solenoid/checking the operation
Adj/set/operate method Enter the value, and then press OK key.
Display/adj/set range 1 to 10
1: Multi Middle Plate Release Solenoid (SL2)
2: Cassette 3 Pickup Solenoid (SL3)
3: Cassette 4 Pickup Solenoid (SL4)
4: Reverse Upper Flapper Solenoid (SL5)
5: Right Deck Pickup Solenoid (SL6)
6: Not used
7: Left Deck Merging Solenoid (SL11)
8: Fixing Cleaning Web Drive Solenoid (SL9)
9: Patch Sensor Shutter Solenoid (SL10)
10: Reverse Detachment Solenoid (SL12)
Default value 1
Related service mode COPIER> FUNCTION> PART-CHK> SL-ON
SL-ON Operation check of Solenoid
To start operation check for the Solenoid specified by SL.
Lv.1 Details
The operation stops after "ON for 0.5 sec" => "OFF for 10 sec" => "ON
for 0.5 sec" => "OFF for 10 sec" => "ON for 0.5 sec".
Use case When replacing the Solenoid/checking the operation
Adj/set/operate method Select the item, and then press OK key.
During operation: ACTIVE, When operation finished normally: OK!
Display/adj/set range
Required time 1 minute
Related service mode COPIER> FUNCTION> PART-CHK> SL
8-117
T-8-50
8-117