112-0001-05
Detection Description
Remedy
112-0002-05
Detection Description
Remedy
197-0000-05
Detection Description
Remedy
197-0100-05
Detection Description
Remedy
Laser Shutter Error
Home position was not detected although the Laser Shutter was closed.
[Related parts] R1.00
- Harness connecting from the Feed/Drum Driver PCB (UN2/J224) to the Laser Shutter Motor and
Laser Shutter Sensor (M28/J6060 and PS29/J6123)
- Laser Shutter Sensor (PS29)
- Laser Shutter Motor (M28)
- Feed/Drum Driver PCB (UN2)
[Remedy] Perform the following in the order while checking whether the error is cleared.
1. Check that the Laser Shutter Motor is properly installed.
2. Check that there is no damage or deformation with the Laser Shutter Sensor Flag.
3. Check/replace the related harness/cable, connector and parts.
Laser Shutter Error
Change in home position was not detected while the Laser Shutter was open.
[Related parts] R1.00
- Harness connecting from the Feed/Drum Driver PCB (UN2/J224) to the Laser Shutter Motor and
Laser Shutter Sensor (M28/J6060 and PS29/J6123)
- Laser Shutter Sensor (PS29)
- Laser Shutter Motor (M28)
- Feed/Drum Driver PCB (UN2)
[Remedy] Perform the following in the order while checking whether the error is cleared.
1. Check that the Laser Shutter Motor is properly installed.
2. Check that there is no damage or deformation with the Laser Shutter Sensor Flag.
3. Check/replace the related harness/cable, connector and parts.
Serial communication error
A communication error between the DC Controller PCB and the Laser Scanner (Y, M) was
detected.
[Related parts] R1.00
- Harness between the DC Controller PCB (UN1/J171) and the Laser Driver PCB (Y) (UN13/J851)
- Small-diameter Coaxial Cable connecting from the Riser PCB (J9) to the Laser Driver PCB (Y)
and (M) (UN13/J802 and UN12/J822)
- Laser Driver PCB (Y) (UN13)
- Laser Driver PCB (M) (UN12)
- Riser PCB
- DC Controller PCB (UN1)
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2
min) and restore the backup data after the replacement so the data may be able to be protected.
- Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP
- Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES
Serial communication error
A communication error between the DC Controller PCB and the Laser Scanner (C, Bk) was
detected.
[Related parts] R1.00
- Harness between the DC Controller PCB (UN1/J171) and the Laser Driver PCB (C) (UN15/J862)
- Small-diameter Coaxial Cable connecting from the Riser PCB (J9) to the Laser Driver PCB (C)
and (Bk) (UN15/J802 and UN14/J822)
- Laser Driver PCB (C) (UN15)
- Laser Driver PCB (Bk) (UN14)
- Riser PCB
- DC Controller PCB (UN1)
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference] Before replacing the DC Controller PCB, back up the service mode data (approx. 2
min) and restore the backup data after the replacement so the data may be able to be protected.
- Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP
- Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES
514
7. Error/Jam/Alarm