Mitsubishi Electric MELSEC iQ-R Series User Manual page 558

Error Error
code (System/
(Hexad axis/axes
ecimal) group)
3465H System
3466H System
3467H System
3468H System
3469H System
346AH System
346BH System
346CH System
346DH System
346EH System
346FH System
3470H System
3471H System
3472H System
3473H System
3474H System
3475H System
3476H System
3477H System
3478H System
22 TROUBLESHOOTING
556
22.5 List of Error Codes
Error name Error detail and cause
Number of Offset/Read/ The value other than
Write Data Incorrect Offset=0,Points=0 is set when
creating a new file.
Out of Current Value The value is out of range for
per Cycle Range Cycle.
Current Value per Cycle FB which does not support the
Change Unsupported current value per cycle change is
set.
No Instance ID The set instance ID does not
exist.
Trigger Input Signal The incorrect data type is set in
Data Type Incorrect TriggerInput.Signal.Source.
Trigger Input Signal The incorrect data name
Data Name specification method is set in
Specification Method
TriggerInput.Signal.Source.
Incorrect
Trigger Input Signal Bit The incorrect bit position is set in
Position Incorrect TriggerInput.Signal.Source.
Trigger Input Signal The incorrect type is set in
Type Incorrect TriggerInput.Signal.Source.
Out of Trigger Input The value is out of range for
Signal Signal Logic TriggerInput.Signal.Detection.
Range
Trigger Input Signal The incorrect target modification
Target Modification is specified in
Incorrect TriggerInput.Signal.Source.
Out of Trigger Input The value is out of range for
Signal Compensation TriggerInput.Signal.Compensatio
Time Range nTime.
SD Memory Card is not SD memory card is not inserted.
Inserted
SD Memory Card is SD memory card is write-
Write-protected protected.
Trigger Input Signal The incorrect data type is set in
Data Type Incorrect TriggerInput.Signal.Source.
Trigger Input Signal The incorrect data name
Data Name specification method is set in
Specification Method TriggerInput.Signal.Source.
Incorrect
Trigger Input Signal The incorrect type is set in
Type Incorrect TriggerInput.Signal.Source.
Trigger Input Signal Bit The incorrect bit position is set in
Position Incorrect TriggerInput.Signal.Source.
Trigger Input Signal The incorrect target modification
Target Modification is specified in
Incorrect TriggerInput.Signal.Source.
Out of Trigger Input The value is out of range for
Signal Signal Logic TriggerInput.Signal.Detection.
Range
Out of Trigger Input The value is out of range for
Signal Compensation TriggerInput.Signal.Compensatio
Time Range nTime.
Detection Operation at
timing (At error
start/ occurrence
during
control
During The execution of FB is
operation interrupted.
During The execution of FB is
operation interrupted.
At start The FB is not
executed.
At start The FB is not
executed.
During The execution of FB is
operation interrupted.
During The execution of FB is
operation interrupted.
During The execution of FB is
operation interrupted.
During The execution of FB is
operation interrupted.
During The execution of FB is
operation interrupted.
During The execution of FB is
operation interrupted.
During The execution of FB is
operation interrupted.
During The execution of FB is
operation interrupted.
During The execution of FB is
operation interrupted.
When Not execute FB.
executing FB
When Not execute FB.
executing FB
When Not execute FB.
executing FB
When Not execute FB.
executing FB
When Not execute FB.
executing FB
When Not execute FB.
executing FB
When Not execute FB.
executing FB
Remedy
Set Offset=0,Points=0
when creating a new file.
Set a value within the
range for Cycle.
Set FB which supports
the current value per
cycle change.
Set the existing instance
ID.
Set a normal data type in
TriggerInput.Signal.Sour
ce.
Set a normal data name
specification method in
TriggerInput.Signal.Sour
ce.
TSet a normal bit
position in
TriggerInput.Signal.Sour
ce.
Set a normal type in
TriggerInput.Signal.Sour
ce.
Set a value within the
range for
TriggerInput.Signal.Dete
ction.
Specify a normal target
modification in
TriggerInput.Signal.Sour
ce.
Set a value within the
range for
TriggerInput.Signal.Com
pensationTime.
Execute it after SD
memory card inserted.
Execute it after
cancelling SD memory
card write-protected.
Set a normal data type.
Set a normal data name
specification method.
Set a normal type.
Set a normal bit position.
Set a normal target
modification.
Set the value within the
range.
Set the value within the
range.