Mitsubishi Electric MELSEC iQ-R Series User Manual page 549

Error Error Error name
code (System/
(Hexad axis/axes
ecimal) group)
1AD0H Axis (All All Axes Forced Stop
axes) Signal Fixed Scan
Refresh Registration
Failure
1AD1H Axis Out of Signal Logical
Setting of FLS Signal
Range
1AD2H Axis Out of Signal Logical
Setting of RLS Signal
Range
1AD3H Axis Out of Signal logical
setting of STOP signal
range
1AD4H Axis Out of Signal Logical
Setting of Forced Stop
Signal Range
1AD5H Axis (All Out of Signal Logical
axes) Setting of All Axes
Forced Stop Signal
Range
1AD8H Axis Out of Master Axis No.
Range
1AD9H Axis Out of Slave Axis No.
Range
1ADAH Axis Out of BufferMode
Range
1ADBH System Command Filter AddOn
System Memory
Shortage
1ADCH System AddOn System Memory
Shortage
1ADEH Axes group Out of Liner Movement
Amount Range
Error detail and cause Detection
timing (At
start/
during
control
Failed to register the At ready ON
"System.Pr.ForcedStop" fixed
cycle refresh.
The value is out of range for At ready ON
"AxisName.Pr.Const.HwStrokeLi
mit_FlsSignal.Detection".
The value is out of range for At ready ON
"AxisName.Pr.Const.HwStrokeLi
mit_RlsSignal.Detection".
The value is out of range for At ready ON
"AxisName.Pr.StopSignal.Detecti
on".
The value is out of range for At ready ON
"AxisName.Pr.ForcedStop.Detect
ion".
The value is out of range for At ready ON
"System.Pr.ForcedStop.Detection
".
The value is out of range for At start
Master.AxisNo. When
executing FB
The value is out of range for At start
Slave.AxisNo. When
executing FB
The value is out of range for At start
BufferMode. When
executing FB
Memory capacity that exceeds At start
the At multipul
"System.PrConst.Addon_AddonL star
ibraryName.RamSizeMax" was
used.
In AddOn related to operation, At start
Memory capacity that exceeds At multipul
the star
"System.PrConst.Addon_AddonL
ibraryName.RamSizeMax" was
used.
The interpolation axis exists in At start
which movement amount At multipul
exceeds '4,294,967,296.0 ( = star
32
2 )' in the linear interpolation for
composite speed specification.
Operation at Remedy
error
occurrence
The signal is detected Increase the memory
continuously. capacity that set in
system. Or, delete
unnecessary axis and
reduce memory size of
axis data to memory
capacity.
The signal is detected Set a value within the
continuously. range for
"AxisName.Pr.Const.Hw
StrokeLimit_FlsSignal.D
etection".
The signal is detected Set a value within the
continuously. range for
"AxisName.Pr.Const.Hw
StrokeLimit_RlsSignal.D
etection".
The signal is detected Set a value within the
continuously. range for
"AxisName.Pr.StopSigna
l.Detection".
The signal is detected Set a value within the
continuously. range for
"AxisName.Pr.ForcedSto
p.Detection".
The signal is detected Set a value within the
continuously. range for
"System.Pr.ForcedStop.
Detection".
The FB is not executed. • Set a value within the
range for
Master.AxisNo.
• Set the axis No. in
which instance is
created.
The FB is not executed. • Set a value within the
range for
Slave.AxisNo.
• Set the axis No. in
which instance is
created.
The FB is not executed. Set a value within the
range for BufferMode.
Not start. Please check the
"System.PrConst.Addon
_AddonLibraryName.Ra
mSizeMax".
Not start. Please check the
"System.PrConst.Addon
_AddonLibraryName.Ra
mSizeMax".
• [At start] Not start. Set the "Position" or
• [At multipul star] Stops "Distance" value so that
the operation. the movement amount of
each interpolation axis
does not exceed
'4,294,967,296.0 ( =
32
2 )'.
22 TROUBLESHOOTING
22.5 List of Error Codes
22
547