Honda ACCORD HYBRID 2005 Service Manual page 21

specs
Item Measurement
Qualification Standard or New Service Limit
Secondary shaft Diameter at bearing contact area 2nd gear 43.986-43.999 m m
(1.7317-1.7322 in.)
When worn or damaged Secondary shaft Diameter at bearing contact area
Torque converter
housing bearing
32.002-32.015 m m
(1.2599-1.2604 in.)
When worn or damaged
Secondary shaft Diameter at bearing contact area
Torque converter
housing bearing
(shaft end side)
28.592-28.608 m m
(1.1257-1.1263 in.)
When worn or damaged
Secondary shaft
Diameter of 1st gear collar at needle
bearing contact area
38.975—38.991 m m
(1.5344-1.5351 in.)
When worn or damaged
Secondary shaft
I.D. of gears 1st gear 44.000—44.016 m m
(1.7323-1.7329 in.)
When worn or damaged
Secondary shaft
I.D. of gears
2nd gear 50.00—50.02 m m
(1.9685-1.9693 in.)
When worn or damaged
Secondary shaft
Axial clearance of gears 1st gear 0.085—0.130 m m
(0.0033-0.0051 in.)
Secondary shaft
Axial clearance of gears
2nd gear
0.06—0.23 m m
(0.0024-0.0091 in.)
Secondary shaft
52 m m thrust washer thickness A 2.405 m m (0.095 in.) When worn or damaged
Secondary shaft
52 m m thrust washer thickness
B 2.430 m m (0.096 in.) When worn or damaged
Secondary shaft
52 m m thrust washer thickness
C 2.455 m m (0.097 in.) When worn or damaged
Secondary shaft
52 m m thrust washer thickness
D
2.480 m m (0.098 in.) When worn or damaged
Secondary shaft
52 m m thrust washer thickness
E 2.505 m m (0.099 in.) When worn or damaged
Secondary shaft
52 m m thrust washer thickness
F 2.530 m m (0.100 in.) When worn or damaged
Secondary shaft
52 m m thrust washer thickness
G 2.555 m m (0.101 in.) When worn or damaged
Secondary shaft
52 m m thrust washer thickness
H 2.580 m m (0.102 in.) When worn or damaged
Secondary shaft
52 m m thrust washer thickness
I
2.605 m m (0.103 in.) When worn or damaged
Secondary shaft
52 m m thrust washer thickness
J 2.630 m m (0.104 in.)
When worn or damaged
Secondary shaft
52 m m thrust washer thickness
K 2.655 m m (0.105 in.) When worn or damaged
Secondary shaft
52 m m thrust washer thickness
L 2.680 m m (0.106 in.)
When worn or damaged
Secondary shaft
52 m m thrust washer thickness
M 2.705 m m (0.106 in.) When worn or damaged
Secondary shaft
1st gear collar length 63.3—63.4 m m
(2.4921-2.4961 in.)
Secondary shaft
2nd gear splined washer thickness 8.966—9.01 m m
(0.353-0.355 in.)
Secondary shaft
Sealing ring thickness 1.91 — 1.97 m m
(0.075-0.078 in.)
1.86 m m (0.073 in.)
Secondary shaft
Sealing ring groove width 2.025-2.060 m m
(0.080—0.081 in.)
2.08 m m (0.082 in.)
Secondary shaft
ATF feed pipe O.D. 1st clutch 11.47—11.48 m m
(0.4516-0.4520 in.)
11.45 m m (0.4508 in.)
Secondary shaft
ATF feed pipe O.D.
1st-hold clutch 5.97—5.98 m m
(0.2350-0.2354 in.)
5.95 m m (0.2343 in.)
Secondary shaft
Feed pipe bushing I.D. 1st clutch 11.518-11.530 m m
(0.4535-0.4539 in.)
11.545 m m (0.4545 in.)
Secondary shaft
Feed pipe bushing I.D.
1st-hold clutch 6.018—6.030 m m
(0.2369-0.2374 in.)
6.045 m m (0.2380 in.)
(cont'd)
2-9