Agilent Technologies InfiniiVision 4000 X-Series Programmer's Manual page 1058

34
:WGEN<w> Commands
Table 145 :WGEN<w> Commands Summary (continued)
Command
:WGEN<w>:RST (see
page 1089)
:WGEN<w>:TRACk {{0 |
OFF} | {1 | ON}} (see
page 1090)
:WGEN<w>:TRACk:AMPLit
ude {{0 | OFF} | {1 |
ON}} (see page 1091)
:WGEN<w>:TRACk:CSIGna
l (see page 1092)
:WGEN<w>:TRACk:FREQue
ncy {{0 | OFF} | {1 |
ON}} (see page 1093)
:WGEN<w>:VOLTage
<amplitude> (see
page 1094)
:WGEN<w>:VOLTage:HIGH
<high> (see
page 1095)
:WGEN<w>:VOLTage:LOW
<low> (see page 1096)
:WGEN<w>:VOLTage:OFFS
et <offset> (see
page 1097)
Introduction to The :WGEN<w> subsystem provides commands to select the waveform
:WGEN<w>
generator function and parameters.
Commands
In the :WGEN<w> commands, the <w> can be 1 or 2, and :WGEN is
equivalent to :WGEN1
Reporting the Setup
Use :WGEN<w>? to query setup information for the WGEN<w> subsystem.
Return Format
The following is a sample response from the :WGEN? query. In this case,
the query was issued following the *RST command.
:WGEN1:FUNC SIN;OUTP 0;FREQ +1.0000E+03;VOLT +500.0E-03;VOLT:OFFS
+0.0E+00;:WGEN1:OUTP:LOAD ONEM
1058
Query
n/a
:WGEN<w>:TRACk? (see
page 1090)
:WGEN<w>:TRACk:AMPLit
ude? (see page 1091)
n/a
:WGEN<w>:TRACk:FREQue
ncy? (see page 1093)
:WGEN<w>:VOLTage?
(see page 1094)
:WGEN<w>:VOLTage:HIGH
? (see page 1095)
:WGEN<w>:VOLTage:LOW?
(see page 1096)
:WGEN<w>:VOLTage:OFFS
et? (see page 1097)
Agilent InfiniiVision 4000 X-Series Oscilloscopes Programmer's Guide
Options and Query Returns
<w> ::= 1 or 2 in NR1 format
{0 | 1}
<w> ::= 1 or 2 in NR1 format
{0 | 1}
<w> ::= 1 or 2 in NR1 format
<w> ::= 1 or 2 in NR1 format
{0 | 1}
<w> ::= 1 or 2 in NR1 format
<amplitude> ::= amplitude in
volts in NR3 format
<w> ::= 1 or 2 in NR1 format
<high> ::= high-level voltage in
volts, in NR3 format
<w> ::= 1 or 2 in NR1 format
<low> ::= low-level voltage in
volts, in NR3 format
<w> ::= 1 or 2 in NR1 format
<offset> ::= offset in volts in
NR3 format
<w> ::= 1 or 2 in NR1 format