Agilent Technologies InfiniiVision 4000 X-Series Programmer's Manual page 1350

Index
turn on/turn off time analysis, 571, 572, 573,
574
turning channel display on and off,
turning off/on function calculation,
turning vectors on or off, 1122
TV mode, 1004, 1166
TV trigger commands, 997, 1002
TV trigger line number setting, 1003
TV trigger mode, 1006
TV trigger polarity, 1005
TV trigger standard setting, 1007
TV triggering, 936
tvmode, 1166
Tx data, UART, 1045
Tx frame count (UART), 779
Tx source, 784
type, USB 2.0 signal quality test,
U
UART base, 785
UART baud rate, 774
UART bit order, 775
UART frame counters, reset, 777
UART parity, 781
UART polarity, 782
UART Rx source, 783
UART SEARch commands, 887
UART serial search, data, 888
UART serial search, data qualifier,
UART serial search, mode, 889
UART trigger burst, 786
UART trigger commands, 770
UART trigger data, 787
UART trigger idle, 788
UART trigger qualifier, 789
UART trigger type, 790
UART Tx data, 1045
UART Tx source, 784
UART width, 791
UART/RS232 demo signal, 295
UART/RS-232 triggering, 646
units (vertical) for FFT, 350
units per division, 280, 281, 335,
units per division (vertical) for function, 280,
363
units, automask, 515
units, X cursor, 400, 401
units, Y cursor, 405, 406
unsigned data, 1025
unsigned mode, 1047
upper threshold, 447
upper threshold voltage for
measurement, 1146
uppercase characters in commands,
URQ (User Request) status bit, 166,
USB (Device) interface, 45
USB 2.0 signal quality test results, save,
USB 2.0 triggering, 646
USB demo signal, 296
USB SEARch commands, 891
USB trigger commands, 792
1350
USB triggering,
user defined channel labels,
268 user defined threshold,
347 user event conditions occurred,
user name, network domain,
User's Guide,
user-defined threshold voltage for digital
channels,
user-defined trigger threshold,
USR (User Event bit), 181,
utilization, CAN bus,
V
valid command strings,
valid pattern time, 981,
292
value, 469
value measured at base of waveform, 435,
value measured at specified time,
value measured at top of waveform,
value ranges,
values required to fill time buckets,
VBA, 56, 1218
Vce(sat) value for conduction calculation,
vectors turned on or off,
vectors, display,
vectors, turning on or off,
vernier, channel,
vernier, horizontal,
890 vertical adjustment, fine (vernier),
vertical amplitude measurement, 433,
vertical axis defined by RANGe,
vertical axis range for channels,
vertical offset for channels,
vertical peak-to-peak measured on
waveform, 436,
vertical scale, 280,
vertical scaling,
vertical threshold,
vertical units for FFT,
vertical value at center screen, 357,
vertical value maximum measured on
waveform,
930 vertical value measurements to calculate
overshoot,
vertical value minimum measured on
waveform,
video line to trigger on,
video standard selection,
view, 226, 1048,
view turns function on or off,
VISA COM example in C#,
VISA COM example in Python,
VISA COM example in Visual Basic,
1209 VISA COM example in Visual Basic .NET,
168 VISA example in C,
VISA example in C#,
625 VISA example in Python,
VISA example in Visual Basic,
VISA example in Visual Basic .NET,
VISA examples, 1218,
Visual Basic .NET, SCPI.NET example,
Agilent InfiniiVision 4000 X-Series Oscilloscopes Programmer's Guide
936
271
1118
183
382
6
307
1165
183
674
1209
982
473
479
480
159
230
606
1122
322
310
282
931
282
471
361
279
272
476
363
1036
1118
350
362
474
444
475
1003
1007
1123
1130
1227
1244
1218
1236
1251
1270
1291
1260
1281
1251
1324
Visual Basic .NET, VISA COM example,
Visual Basic .NET, VISA example,
Visual Basic 6.0, 57
Visual Basic for Applications, 56,
Visual Basic, SICL library example,
Visual Basic, VISA COM example,
Visual Basic, VISA example, 1260
visualizations, math, 359
voltage crossing reported or not found,
voltage difference between data points,
voltage difference measured, 1147
voltage level for active trigger, 962
voltage marker used to measure
waveform, 1148, 1149
voltage offset value for channels,
voltage probe, 281, 335
voltage ranges for channels, 279
voltage ranges for external trigger,
voltage source, 599
voltage threshold, 428
voltage, maximum expected input, 592, 593,
594
W
WAI (Wait To Continue), 186
wait, 186
wait for operation complete, 172
Wait Trig bit, 211, 213
waveform base value measured, 435,
WAVeform command, 55
WAVeform commands, 1019
waveform data, 1021
waveform data format, 639
waveform data length, 640
waveform data length, maximum,
waveform data, save, 638
waveform generator, 1058
waveform generator amplitude, 1094
waveform generator function, 1067
waveform generator high-level voltage,
waveform generator low-level voltage,
waveform generator offset, 1097
waveform generator output control,
waveform generator output load
impedance, 1086
waveform generator output polarity,
waveform generator period, 1088
waveform generator pulse width,
waveform generator ramp symmetry,
waveform generator reset defaults,
waveform generator square wave duty
cycle, 1072
waveform introduction, 1021
waveform maximum vertical value
measured, 474
waveform minimum vertical value
measured, 475
waveform must cross voltage level to be an
occurrence, 1144
WAVeform parameters, 60
1236
1281
1218
1307
1218
1144
1052
272
334
473
641
1095
1096
1085
1087
1070
1071
1089