Agilent Technologies InfiniiVision 4000 X-Series Programmer's Manual page 1342

Index
handshake PID, USB trigger, 811
HANNing window for frequency
resolution, 351
hardcopy, 219, 370
HARDcopy commands, 369
hardcopy factors, 373, 628
hardcopy filename, 1132
hardcopy format, 1131
hardcopy formfeed, 374
hardcopy grayscale, 1133
hardcopy invert graticule colors, 375,
hardcopy layout, 376
hardcopy palette, 383
hardcopy print, area, 371
hardcopy printer driver, 1135
Hardware Event Condition Register
(:HWERegister:CONDition),
Hardware Event Condition Register
(:OPERegister:CONDition), 1193
Hardware Event Enable Register
(HWEenable), 201
Hardware Event Event Register
(:HWERegister[:EVENt]), 204,
head type, probe, 274
header, 1209
high pass filter math function, 359
high resolution acquisition type, 1023
high trigger level, 942
high-frequency reject filter, 939,
high-level voltage, waveform generator,
high-pass filter cutoff frequency,
high-resolution acquisition type,
hold time, setup and hold trigger,
hold until operation complete, 172
holdoff time, 940
holes in waveform data, 1029
hop frequency, waveform generator FSK
modulation, 1077
horizontal adjustment, fine (vernier),
horizontal position, 932
horizontal scale, 930, 934
horizontal scaling, 1036
horizontal time, 927, 933, 1138
Host name softkey, 46
hostname, 46
hub address value, USB search, 901
hub address value, USB trigger, 808
HWEenable (Hardware Event Enable
Register), 201
HWERegister:CONDition (Hardware Event
Condition Register), 203, 1193
HWERegister[:EVENt] (Hardware Event Event
Register), 204, 1192
I
I1080L50HZ, 1003, 1007
I1080L60HZ, 1003, 1007
I2C demo signal, 295
I2S alignment, 706
I2S audio channel, 715
I2S clock slope, 708
1342
I2S CLOCk source,
I2S DATA source,
I2S demo signal,
I2S pattern data,
I2S pattern format,
I2S range, 719
I2S receiver width,
I2S SEARch commands,
I2S serial bus commands,
I2S serial decode base,
1134 I2S serial search, audio channel,
I2S serial search, data,
I2S serial search, format,
I2S serial search, mode,
I2S serial search, range,
I2S transmit word size,
203 I2S trigger operator,
I2S triggering,
I2S word select (WS) low,
I2S word select (WS) source,
id mode, 684
ID pattern, CAN trigger,
1192 identification number,
identification of options,
identifier, LIN,
idle, 956
idle until operation complete,
IDN (Identification Number),
963 IEC 61000-3-2 standard for current harmonics
1095 analysis,
352 IEEE 488.2 standard,
228 IIC address, 727
995 IIC clock, 725
IIC data, 726,
IIC data 2, 729
IIC SEARch commands,
IIC serial decode address field size,
IIC serial search, address,
931 IIC serial search, data,
IIC serial search, data2,
IIC serial search, mode,
IIC serial search, qualifier,
IIC trigger commands,
IIC trigger qualifier,
IIC trigger type,
IIC triggering,
image format,
image invert graticule colors,
image memory,
image palette,
image, save,
image, save with inksaver,
impedance, 269
infinity representation,
initial load current, transient response
analysis,
initialization, 54,
initialize, 176,
initialize label list,
initiate acquisition,
inksaver, save image with,
input coupling for channels,
Agilent InfiniiVision 4000 X-Series Oscilloscopes Programmer's Guide
710
711
296
716
718
709
860
704
707
861
863
864
862
865
721
713
645
722
712
683
170
173
742
172
170
562
164
728
866
724
869
870
871
867
872
723
730
731
646
629
630
223
631
627
630
1215
610
57
915
318
199
630
267
input for integrate, DC offset correction,
input impedance for channels, 269,
input inversion for specified channel,
input power, 496
inrush current, 500
inrush current analysis, 565, 566,
inrush current expected, 590
insert label, 271
installed options identified, 173
instruction header, 1209
instrument number, 170
instrument options identified, 173
instrument requests service, 183
instrument serial number, 221
instrument settings, 370
instrument status, 64
instrument type, 170
integrate DC offset correction, 354
integrate math function, 358, 1041
INTegrate source for function, 1129
internal low-pass filter, 266, 332
introduction to :ACQuire commands,
introduction to :BUS<n> commands,
introduction to :CALibrate commands,
introduction to :CHANnel<n> commands,
introduction to :DEMO commands,
introduction to :DIGital<d> commands,
introduction to :DISPlay commands,
introduction to :EXTernal commands,
introduction to :FUNCtion commands,
introduction to :HARDcopy commands,
introduction to :LISTer commands,
introduction to :MARKer commands,
introduction to :MEASure commands,
introduction to :POD<n> commands,
introduction to :RECall commands,
introduction to :SAVE commands,
introduction to :SBUS commands,
introduction to :SYSTem commands,
introduction to :TIMebase commands,
introduction to :TRIGger commands,
introduction to :WAVeform commands,
introduction to :WGEN<w> commands,
introduction to :WMEMory<r>
commands, 1099
introduction to common (*) commands,
introduction to root (:) commands,
invert graticule colors for hardcopy, 375,
invert graticule colors for image,
inverted masks, bind levels, 534
inverting input for channels, 270
IO library, referencing, 56
IP address, 46
IronPython, SCPI.NET example, 1330
K
key disable, 914
key press detected in Standard Event Status
Register, 168
knob disable, 914
known state, 176, 915
354
1120
270
567
227
244
254
265
293
302
310
331
340
370
387
392
420
541
614
623
645
910
924
935
1021
1058
164
190
1134
630