Agilent Technologies InfiniiVision 4000 X-Series Programmer's Manual page 1340

Index
delta time, 1138
delta voltage measurement, 1147
delta X cursor, 392
delta Y cursor, 392
demo, 293
DEMO commands, 293
demo signal, 295
demo signal function, 294
demo signal phase angle, 298
demo signals output control, 299
deskew for power measurements,
detecting probe types, 1121, 1125
device-defined error queue clear,
DIFF source for function, 1129
differences from 3000 X-Series oscilloscope
commands, 37
differential D+ and D- USB signal source,
differential probe heads, 274
differential probe source, USB 2.0 signal quality
test, 287
differential signal type, 277
differentiate math function, 358,
digital channel commands, 302, 303, 304, 305,
307
digital channel data, 1026
digital channel labels, 318
digital channel order, 1123
digital channel source for glitch trigger,
digital channels, 6
digital channels, activity and logic levels
on, 191
digital channels, groups of, 541, 543,
digital pod, stop displaying, 198
digital reset conditions, 177, 916
DIGital<d> commands, 301
digitize channels, 199
DIGitize command, 54, 59, 1022
digits, 159
disable front panel, 914
disable function, 1130
disabling calibration, 258
disabling channel display, 268
disabling status register bits, 166,
discontinued and obsolete commands,
display annotation, 311
display annotation background, 312
display annotation color, 313
display annotation text, 314
display channel labels, 317
display clear, 315
DISPlay commands, 309
display commands introduction, 310
display connect, 1122
display date, 911
display factors scaling, 273
display for channels, 268
display frequency span, 349
display measurements, 420, 457
display order, 1123
display persistence, 321
display reference, 926, 929
display reference waveforms, 1102
1340
display reset conditions, 177,
display serial number,
display vectors,
display wave position,
display, lister,
display, measurement statistics on/off,
display, oscilloscope, 303, 321, 347, 543,
display, serial decode bus,
displaying a baseline,
displaying unsynchronized signal,
552 divide math function,
DNS IP, 46
165 domain, 46
domain, network printer,
driver, printer,
DSO models,
798 duplicate mnemonics,
duration, 981, 982,
duration for glitch trigger, 968, 969,
duration of power analysis, 584, 585, 586,
587, 588,
1041 duration qualifier, trigger, 981,
duration triggering,
duty cycle measurement, 55, 420,
Duty Cycle, power modulation analysis,
DVM commands,
DVM displayed value,
974 DVM enable/disable,
DVM frequency value,
DVM input source,
DVM mode, 328
545
E
EBURst trigger commands,
ECL channel threshold,
ECL threshold voltage for digital channels,
ECL trigger threshold voltage,
edge activity,
edge counter, Edge Then Edge trigger,
edge counter, Nth edge of burst,
edge coupling,
180
edge fall time,
1109
edge parameter for delay measurement,
edge preshoot measured,
edge rise time,
EDGE SEARch commands,
edge search slope,
edge search source,
edge slope, 964
edge source,
edge string for OR'ed edge trigger,
EDGE trigger commands,
edge triggering,
edges (activity) on digital channels,
edges in measurement,
efficiency, 493
efficiency power analysis, apply,
elapsed time in mask test,
ellipsis, 159
enable channel labels,
enabling calibration,
Agilent InfiniiVision 4000 X-Series Oscilloscopes Programmer's Guide
916
221
322
1123
389
461
912
648
946
946
358
379
1135
6
1213
985
973
589
982
936
438
570
323
325
326
327
329
954
1118
307
1165
1116
951
955
961
439
430
450
455
822
823
824
965
976
959
936
191
428
553
520
317
258
enabling channel display, 268
enabling status register bits, 166,
end of string (EOS) terminator, 1210
end of text (EOT) terminator, 1210
end or identify (EOI), 1210
endpoint value, USB search, 898
endpoint value, USB trigger, 805
energy loss, 494
EOI (end or identify), 1210
EOS (end of string) terminator, 1210
EOT (end of text) terminator, 1210
equivalent time acquisition mode,
erase data, 315
erase measurements, 1137
erase screen, 1124
error counter (ARINC 429), 654
error counter (ARINC 429), reset,
error frame count (CAN), 670
error frame count (UART), 776
error messages, 913, 1167
error number, 913
error queue, 913, 1187
error, measurement, 420
ESB (Event Status Bit), 181, 183
ESE (Standard Event Status Enable
Register), 166, 1186
ESR (Standard Event Status Register), 168,
1185
ET value, USB search, 899
ET value, USB trigger, 806
ETE demo signal, 295
event status conditions occurred,
Event Status Enable Register (ESE), 166,
Event Status Register (ESR), 168, 225,
example code, :ACQuire:COMPlete,
example code, :ACQuire:SEGMented,
example code, :ACQuire:TYPE, 241
example code, :AUToscale, 194
example code, :CHANnel<n>:LABel,
example code, :CHANnel<n>:PROBe,
example code, :CHANnel<n>:RANGe,
example code, :DIGitize, 200
example code, :DISPlay:DATA, 316
example code, :DISPlay:LABel, 317
example code, :DISPlay:ORDer, 1123
example code, :MEASure:PERiod,
example code, :MEASure:RESults,
example code, :MEASure:TEDGe,
example code, :MTESt, 509
example code, :POD<n>:THReshold,
example code, :RUN/:STOP, 220
example code, :SYSTem:SETup, 919
example code, :TIMebase:DELay,
example code, :TIMebase:MODE,
example code, :TIMebase:RANGe,
example code, :TIMebase:REFerence,
example code, :TRIGger:MODE,
example code, :TRIGger:SLOPe,
example code, :TRIGger:SOURce,
example code, :VIEW and :BLANk,
example code, :WAVeform, 1042
example code, :WAVeform:DATA,
180
231
655
183
1186
1185
229
236
271
273
279
459
452
467
545
1164
925
927
929
944
964
965
226
1029