Agilent Technologies InfiniiVision 4000 X-Series Programmer's Manual page 1348

Index
source, automask, 514
source, FLEXray, 694
source, mask test, 539
source, runt search, 835
source, runt trigger, 989
source, save reference waveform,
source, transition trigger, 840, 1000
source, trigger edge, Edge Then Edge
trigger, 953
source, waveform, 1041
span, 358
span of frequency on display, 349
special PID, USB search, 904
special PID, USB trigger, 812
specify measurement, 458
speed of ARINC 429 signal, 660
speed, USB decode, 799
SPI, 757
SPI clock timeout, 758
SPI decode bit order, 756
SPI decode word width, 769
SPI demo signal, 296
SPI MISO data, 1045
SPI SEARch commands, 883
SPI serial search, data, 885
SPI serial search, data width, 886
SPI serial search, mode, 884
SPI trigger, 759, 765, 767
SPI trigger clock, 760
SPI trigger commands, 754
SPI trigger frame, 761
SPI trigger MISO data pattern, 764
SPI trigger MOSI data pattern, 766
SPI trigger type, 768
SPI trigger, MISO data source, 762
SPI trigger, MOSI data source, 763,
SPI triggering, 646
square math function, 358
square root math function, 358
square wave duty cycle, waveform
generator, 1072
square waveform generator output,
SRE (Service Request Enable Register), 181,
1181
SRQ (Service Request interrupt), 201, 205,
SSM pattern, ARINC 429 trigger, 664,
standard deviation measured on
waveform, 456
Standard Event Status Enable Register
(ESE), 166, 1186
Standard Event Status Register (ESR), 168,
1185
standard for video, 1007
standard, LIN, 739
start acquisition, 184, 199, 220,
start and stop edges, 428
start cursor, 1142
start measurement, 420
start print job, 385
start time, 973, 1142
start time marker, 1139
state memory, 179
1348
state of instrument, 171,
statistics increment,
statistics reset,
statistics results,
statistics, max count,
643 statistics, relative standard deviation,
statistics, type of,
status, 182, 223,
Status Byte Register (STB), 180, 182, 183,
1179
status data structure clear,
status registers,
status reporting,
STB (Status Byte Register), 180, 182, 183,
1179
steady state output voltage expected, 595,
596, 597
step size for frequency span,
stop, 199, 224
stop acquisition,
stop cursor, 1143
stop displaying channel,
stop displaying math function,
stop displaying pod,
stop on mask test failure,
stop time, 973,
storage, 179
store instrument setup, 171,
store setup, 179
storing calibration information,
string variables,
string variables, reading multiple query results
into, 63
string variables, reading query results into
multiple,
1162 string, quoted ASCII,
subnet mask,
subsource, waveform source,
subsystem commands, 3,
subtract math function, 358,
subtract math function as g(t) source,
1067 sweep mode, trigger, 935,
sweep speed set to fast to measure fall
time, 439
209 sweep speed set to fast to measure rise
847 time, 455
switch disable,
switching level, current,
switching level, voltage,
switching loss per cycle,
switching loss power analysis,
sync break, LIN,
sync frame count (FlexRay),
syntax elements,
222 syntax rules, program data,
syntax, optional terms,
syntax, program message,
SYSTem commands,
system commands, 911, 912, 913, 914, 919,
921
system commands introduction,
Agilent InfiniiVision 4000 X-Series Oscilloscopes Programmer's Guide
919
462
464
452
463
465
460
225
165
64
1175
349
224
198
198
198
530
1143
179
256
62
63
159
46
1045
1213
1041
1126
946
914
604
607
491
602
740
692
158
1212
158
1209
909
910
T
table of current harmonics results,
tdelta, 1138
tedge, 466
telnet ports 5024 and 5025, 1029
Telnet sockets, 65
temporary message, 912
TER (Trigger Event Register), 225,
termination conditions, mask test,
test sigma, mask test run, 531
test, self, 185
test, USB 2.0 signal quality, 290
text, writing to display, 912
THD (total harmonics distortion),
threshold, 307, 545, 1118, 1165
threshold voltage (lower) for
measurement, 1136
threshold voltage (upper) for
measurement, 1146
thresholds, 428, 1139
thresholds used to measure period,
thresholds, how autoscale affects,
time base, 925, 926, 927, 929, 930,
time base commands introduction,
time base reset conditions, 177,
time base window, 932, 933, 934
time between points, 1138
time buckets, 229, 230
time delay, 1164
time delay, Edge Then Edge trigger,
time delta, 1138
time difference between data points,
time duration, 973, 981, 982, 985
time holdoff for trigger, 940
time interval, 466, 469, 1138
time interval between trigger and
occurrence, 1144
time marker sets start time, 1139
time measurements with X cursors,
time per division, 927
time record, 351
time reference, lister, 390
time specified, 479
time, calibration, 262
time, mask test run, 532
time, runt pulse search, 836
time, runt trigger, 990
time, start marker, 1142
time, stop marker, 1143
time, system, 921
time, transition search, 841
time, transition trigger, 1001
time/div, how autoscale affects,
time-at-max measurement, 1140
time-at-min measurement, 1141
TIMebase commands, 923
timebase vernier, 931
TIMebase:MODE, 60
time-ordered label list, 318
timeout, SPI clock, 758
timing measurement, 420
557
1182
526
564
447
193
1164
924
916
950
1049
400
193