Agilent Technologies InfiniiVision 4000 X-Series Programmer's Manual page 1344

Index
measurements, delay, 430
measurements, duty cycle, 438
measurements, fall time, 439
measurements, falling edge count,
measurements, falling pulse count,
measurements, frequency, 440
measurements, how autoscale affects,
measurements, lower threshold level,
measurements, maximum vertical value,
measurements, maximum vertical value, time
of, 482, 1140
measurements, minimum vertical value,
measurements, minimum vertical value, time
of, 483, 1141
measurements, overshoot, 444
measurements, period, 447
measurements, phase, 448
measurements, preshoot, 450
measurements, pulse width, negative,
measurements, pulse width, positive,
measurements, ratio of AC RMS values,
measurements, rise time, 455
measurements, rising edge count,
measurements, rising pulse count,
measurements, show, 457
measurements, snapshot all, 422
measurements, source channel, 458
measurements, standard deviation,
measurements, start marker time,
measurements, stop marker time,
measurements, thresholds, 1139
measurements, time between start and stop
markers, 1138
measurements, time between trigger and
edge, 466
measurements, time between trigger and
vertical value, 469
measurements, time between trigger and
voltage level, 1144
measurements, upper threshold value,
measurements, vertical amplitude, 433,
measurements, vertical peak-to-peak, 436,
measurements, voltage difference,
memory setup, 179, 919
menu, display, 319
menu, system, 1163
message available bit, 183
message available bit clear, 165
message displayed, 183
message error, 1167
message queue, 1184
messages ready, 183
midpoint of thresholds, 447
MIL-STD-1553 demo signal, 296
MIL-STD-1553 serial decode base,
MIL-STD-1553 serial search, data,
MIL-STD-1553 serial search, mode,
MIL-STD-1553 serial search, Remote Terminal
Address, 882
MIL-STD-1553, dual demo signal,
minimum duration, 968, 981, 982,
minimum vertical value measurement,
1344
minimum vertical value, time of, 483,
MISO data pattern width,
MISO data pattern, SPI trigger,
441 MISO data source, SPI trigger,
442 MISO data, SPI,
mixed-signal demo signals,
193 mixed-signal oscilloscopes,
1136 mnemonics, duplicate,
474 mode, 394, 925,
mode, serial decode,
model number,
475 models, oscilloscope,
modes for triggering,
Modify softkey,
modulating signal frequency, waveform
generator, 1074,
modulation (waveform generator),
enabling/disabling,
443 modulation analysis,
451 modulation analysis source (voltage or
477 current), 569
modulation analysis, type of,
446 modulation type, waveform generator,
449 MOSI data pattern width,
MOSI data pattern, SPI trigger,
MOSI data source, SPI trigger, 763,
most significant byte first,
456 move cursors, 1142,
1142 msbfirst, 1027
1143 MSG (Message), 181,
MSO models, 6
MSS (Master Summary Status),
MTEenable (Mask Test Event Enable
Register),
MTERegister[:EVENt] (Mask Test Event Event
Register), 207,
MTESt commands,
multi-channel waveform data, save,
multiple commands,
1146 multiple queries,
471 multiply math function, 358,
476 multiply math function as g(t) source,
1147
N
N2820A high sensitivity current probe, 34, 432,
433, 434, 435, 436,
N8900A InfiniiView oscilloscope analysis
software,
name channels,
name list, 318
natural logarithm math function,
negative glitch trigger polarity,
negative pulse width,
749
negative pulse width measurement,
881
negative pulse width, power modulation
880
analysis, 570
negative slope, 757,
negative slope, Nth edge in burst,
296
negative TV trigger polarity,
985
network domain password,
475
network domain user name,
Agilent InfiniiVision 4000 X-Series Oscilloscopes Programmer's Guide
1141
765
764
762
1045
295
6
1213
1004
649
170
3
944
46
1076
1082
568
570
1083
767
766
1162
1027
1143
183
183
205
1194
507
634
1213
63
1041
1126
437
634
271
358
971
443
55
964
957
1005
380
382
network printer address, 377
network printer domain, 379
network printer slot, 381
network printer, apply connection settings,
new line (NL) terminator, 158, 1210
new load current, transient response
analysis, 611
NL (new line) terminator, 158, 1210
NMONotonic, dual demo signal,
noise floor, 604, 607
noise reject filter, 945
noise waveform generator output,
noise, adding to waveform generator
output, 1081
noisy sine waveform demo signal,
non-core commands, 1208
non-interlaced GENeric mode, 1007
non-volatile memory, label list, 250, 304,
normal acquisition type, 228, 1022
normal trigger sweep mode, 935
notices, 2
NR1 number format, 158
NR3 number format, 158
Nth edge burst trigger source, 958
Nth edge burst triggering, 936
Nth edge in a burst idle, 956
Nth edge in burst slope, 957
Nth edge of burst counter, 955
Nth edge of Edge Then Edge trigger,
NTSC, 1003, 1007
null frame count (FlexRay), 690
null offset, 604
NULL string, 912
number format, 158
number of points, 232, 1032, 1034
number of time buckets, 1032, 1034
numeric variables, 62
numeric variables, reading query results into
multiple, 64
nwidth, 443
O
obsolete and discontinued commands,
obsolete commands, 1208
occurrence reported by magnitude,
offset, 340
offset for Ax + B math operation,
offset value for channel voltage,
offset value for selected function, 357,
offset, waveform generator, 1097
one values in waveform data, 1029
OPC (Operation Complete) command,
OPC (Operation Complete) status bit, 166,
OPEE (Operation Status Enable Register),
Open method, 57
operating configuration, 171, 919
operating state, 179
operation complete, 172
operation status condition register,
Operation Status Condition Register
(:OPERegister:CONDition), 211,
378
296
1068
294
318
951
1109
1144
356
272
362
172
168
209
211
1189