Agilent Technologies InfiniiVision 4000 X-Series Programmer's Manual page 1349

title channels, 271
title, mask test, 540
token PID, USB search, 905
token PID, USB trigger, 813
tolerance, automask, 516, 517
top of waveform value measured,
total frame count (CAN), 673
total frame count (FlexRay), 693
total harmonics distortion (THD),
total waveforms in mask test, 521
touchscreen on/off, 922
trace memory, 223
track measurements, 457
tracking, dual channel waveform
generator, 1090
trademarks, 2
transfer instrument state, 171, 919
transforms, math, 358
transient response, 505
transient response analysis, 608, 609,
TRANsition SEARch commands,
transition search qualifier, 838
transition search slope, 839
transition search time, 841
transition trigger qualifier, 998
transition trigger slope, 999
transition trigger source, 840, 1000
transition trigger time, 1001
transmit word size, I2S, 721
tree traversal rules, 1213
trend measurement, 367
TRG (Trigger), 181, 183, 184
TRIG OUT BNC, 257
trigger armed event register, 211,
trigger burst, UART, 786
trigger channel source, 974, 1006
TRIGger commands, 935
TRIGger commands, general, 937
trigger data, UART, 787
TRIGger DELay commands, 947
trigger duration, 981, 982
TRIGger EBURst commands, 954
TRIGger EDGE commands, 959
trigger edge coupling, 961
trigger edge slope, 964
trigger edge slope, Edge Then Edge
trigger, 952
trigger edge source, Edge Then Edge
trigger, 953
trigger event bit, 225
Trigger Event Register (TER), 1182
TRIGger FLEXray commands, 685
TRIGger GLITch commands, 966
trigger holdoff, 940
trigger idle, UART, 788
TRIGger IIC commands, 723
trigger level auto set up, 941
trigger level constants, 273
trigger level voltage, 962
trigger level, high, 942
trigger level, low, 943
TRIGger LIN commands, 733
Agilent InfiniiVision 4000 X-Series Oscilloscopes Programmer's Guide
TRIGger M1553 commands,
trigger occurred,
TRIGger OR commands,
TRIGger PATTern commands,
trigger pattern qualifier,
480 trigger qualifier, UART,
trigger reset conditions, 177,
TRIGger RUNT commands,
564 TRIGger SHOLd commands,
trigger SPI clock slope,
TRIGger SPI commands,
trigger status bit,
trigger sweep mode,
TRIGger TV commands, 997,
trigger type, ARINC 429, 666,
trigger type, SPI,
trigger type, UART,
TRIGger UART commands,
TRIGger USB commands,
612 TRIGger ZONE commands,
837 trigger, ARINC 429 source,
trigger, CAN,
trigger, CAN pattern data length,
trigger, CAN pattern ID mode,
trigger, CAN sample point,
trigger, CAN signal baudrate,
trigger, CAN signal definition,
trigger, CAN source,
trigger, duration greater than,
trigger, duration less than,
trigger, duration range,
trigger, edge coupling,
trigger, edge level,
213 trigger, edge reject,
trigger, edge slope,
trigger, edge source,
trigger, FLEXray,
trigger, FLEXray error,
trigger, FLEXray event,
trigger, force a,
trigger, glitch greater than,
trigger, glitch less than,
trigger, glitch level,
trigger, glitch polarity,
trigger, glitch qualifier,
trigger, glitch range,
trigger, glitch source,
trigger, high frequency reject filter,
trigger, holdoff,
trigger, I2S, 713
trigger, I2S alignment,
trigger, I2S audio channel,
trigger, I2S clock slope,
trigger, I2S CLOCksource,
trigger, I2S DATA source,
trigger, I2S pattern data,
trigger, I2S pattern format,
trigger, I2S range,
trigger, I2S receiver width,
trigger, I2S transmit word size,
trigger, I2S word select (WS) low,
trigger, I2S word select (WS) source,
747
183
975
977
983
789
916
986
991
757
754
225
935
1002
844
768
790
770
792
1012
659
679
682
684
675
676
677
678
981
982
985
961
962
963
964
965
695
696
699
938
968
969
970
971
972
973
974
939
940
706
715
708
710
711
716
718
719
709
721
722
712
trigger, IIC clock source, 725
trigger, IIC data source, 726
trigger, IIC pattern address, 727
trigger, IIC pattern data, 728
trigger, IIC pattern data 2, 729
trigger, IIC qualifier, 730
trigger, IIC signal baudrate, 737
trigger, IIC type, 731
trigger, LIN, 741
trigger, LIN pattern data, 743
trigger, LIN pattern data length, 745
trigger, LIN pattern format, 746
trigger, LIN sample point, 736
trigger, LIN signal definition, 1161
trigger, LIN source, 738
trigger, mode, 944
trigger, noise reject filter, 945
trigger, Nth edge burst source, 958
trigger, Nth edge in burst slope, 957
trigger, Nth edge of burst count,
trigger, Nth edge of Edge Then Edge
trigger, 951
trigger, SPI clock slope, 757
trigger, SPI clock source, 760
trigger, SPI clock timeout, 758
trigger, SPI frame source, 761
trigger, SPI framing, 759
trigger, SPI pattern MISO width,
trigger, SPI pattern MOSI width,
trigger, sweep, 946
trigger, threshold, 1165
trigger, TV line, 1003
trigger, TV mode, 1004, 1166
trigger, TV polarity, 1005
trigger, TV source, 1006
trigger, TV standard, 1007
trigger, UART base, 785
trigger, UART baudrate, 774
trigger, UART bit order, 775
trigger, UART parity, 781
trigger, UART polarity, 782
trigger, UART Rx source, 783
trigger, UART Tx source, 784
trigger, UART width, 791
trigger, USB, 800
truncation rules, 1210
TST (Self Test), 185
tstart, 1142
tstop, 1143
TTL threshold voltage for digital channels, 307,
1118
TTL trigger threshold voltage, 1165
turn function on or off, 1130
turn off channel, 198
turn off channel labels, 317
turn off digital pod, 198
turn off math function, 198
turn off time, 497, 574
turn on channel labels, 317
turn on channel number display,
turn on time, 498, 574
Index
955
765
767
1123
1349