Honda Accord 2008 Manual page 23

07/11/02 09:02:40 61TA0000_020_0008
Standards and Service Limits
Manual Transmission and M/T Differential (cont'd)
Item
Reverse idler I.D.
gear Gear-to-reverse gear shaft clearance
Synchro ring Ring-to-gear clearance
Double cone Outer synchro ring-to-synchro cone
synchro clearance
Synchro cone-to-gear clearance
Outer synchro ring-to-gear cone
clearance
Triple cone Outer synchro ring-to-synchro cone
synchro clearance
Synchro cone-to-gear clearance
Outer synchro ring-to-gear cone
clearance
Shift fork Finger width
Fork-to-synchro sleeve clearance
Reverse shift Finger width
fork Fork-to-reverse idler gear clearance
Shift arm I.D.
Shift arm width
Shift arm-to-shift piece clearance
Select lever Finger width
Change lever Shift-to-select lever clearance
Groove (to select lever) width
Shaft-to-shift arm clearance
M/T differential Pinion shaft contact area I.D.
carrier Carrier-to-pinion shaft clearance
Driveshaft contact area I.D.
M/T differential Backlash
pinion gear I.D.
Pinion gear-to-pinion shaft clearance
M/T differential 80 mm shim-to-bearing outer race
80 mm shim clearance in transmission housing
2-8
Measurement Qualification
Ring pushed
against gear
Ring pushed
against gear
Ring pushed
against gear
Ring pushed
against gear
Ring pushed
against gear
Ring pushed
against gear
Ring pushed
against gear
Standard or New
− −
20.016 20.043 mm (0.7880 0.7891 in.) 20.90 mm (0.832 in.)
0.036 0.084 mm (0.0014 0.0033 in.) − −
0.70 1.49 mm (0.028 0.059 in.) − −
0.70 1.19 mm (0.028 0.047 in.) − −
− −
0.50 1.04 mm (0.020 0.041 in.)
0.95 1.68 mm (0.037 0.066 in.) − −
0.70 1.19 mm (0.028 0.047 in.) − −
0.50 1.04 mm (0.020 0.041 in.) − −
− −
0.95 1.68 mm (0.037 0.066 in.)
7.4 7.6 mm (0.29 0.30 in.) − −
0.35 0.65 mm (0.014 0.026 in.) − −
13.4 13.7 mm (0.527 0.539 in.) − −
0.20 0.59 mm (0.007 0.024 in.) − −
− −
13.973 14.000 mm (0.5501 0.5512 in.)
− −
16.9 17.0 mm (0.665 0.669 in.)
0.2 0.5 mm (0.008 0.020 in.) − −
14.85 14.95 mm (0.585 0.589 in.) − −
0.05 0.25 mm (0.002 0.010 in.) − −
15.00 15.10 mm (0.591 0.594 in.) − −
0.013 0.07 mm (0.0005 0.003 in.) − −
− −
18.010 18.028 mm (0.7091 0.7098 in.)
− −
0.027 0.057 mm (0.0011 0.0022 in.)
28.025 28.045 mm (1.1033 1.1041 in.) − −
0.05 0.15 mm (0.002 0.006 in.) − −
18.042 18.066 mm (0.7103 0.7113 in.) − −
0.059 0.095 mm (0.0023 0.0037 in.) − −
0 0.10 mm (0 0.0039 in.) − −
Service Limit
0.16 mm (0.006 in.)
0.4 mm (0.016 in.)
0.3 mm (0.012 in.)
0.3 mm (0.012 in.)
0.6 mm (0.024 in.)
0.3 mm (0.012 in.)
0.3 mm (0.012 in.)
0.6 mm (0.024 in.)
―――
1.0 mm (0.039 in.)
―――
1.2 mm (0.047 in.)
―――
―――
0.6 mm (0.024 in.)
―――
0.5 mm (0.020 in.)
―――
0.1 mm (0.004 in.)
―――
0.1 mm (0.004 in.)
―――
―――
―――
0.15 mm (0.006 in.)
Adjust