Xerox ColorQube 9303 Series Service Manual page 566

Table 7 Chain 12 Status codes
Status
Code UI Message
12-627-02 Paper jam in the finisher
12-628-00 Paper jam in the finisher
12-629-00 Paper jam in the finisher
12-630-01 Paper jam in the finisher
12-630-02 Paper jam in the finisher
12-636-01 Paper jam in the finisher
12-636-02 Paper jam in the finisher
12-640-00 Hole punch not detected
(missing). Please insert
the hole punch.
12-641-00 The hole punch waste
container is not detected.
Please re-insert.
Status Indicator RAPs
OF 4a
Reason for Message Reference / Action
Page over the exit HVF into Clear the paper jam
BM sensor (sensor in area
6a) cleared via area 6a
Sheet over the stacker bin Clear the area. If the
exit sensor problem persists, per-
form the
12-152-171
Sheet over the tri-folder entry Clear the area. If the
sensor problem persists, per-
form the
171, 12-184-00-171
RAP
Sheet over the booklet maker Clear the area. If the
entry sensor (without tri- problem persists, per-
folder) form the
171, 12-184-00-171
RAP
Sheet over the booklet maker Clear the area. If the
entry sensor (with tri-folder) problem persists, per-
form the
171, 12-184-00-171
RAP
Sheet over the booklet maker Clear the jam from the
exit sensor (without tri-folder) output bin. If the prob-
lem persists, perform
the 12-181-00-171,
12-182-00-171
Sheet over the booklet maker Clear the jam from the
exit sensor (with tri-folder) output bin. If the prob-
lem persists, perform
the 12-181-00-171,
12-182-00-171
The finisher punch unit is Make sure that the
missing or incorrectly punch unit is cor-
installed. rectly installed.
If the problem per-
sists, perform the
043-00-110, 12-046-
00-110 RAP
The chad bin has been Reinstall the chad bin.
removed from the finisher If the problem per-
sists, perform the
043-00-110, 12-046-
00-110 RAP
Status
Code UI Message
12-642-00 Booklet maker staples
low. Re-order booklet sta-
ple cartridge
12-151-171,
12-643-00 Booklet maker staple car-
tridge is empty
12-183-00-
12-183-00-
12-643-01 Booklet maker staple car-
tridge is empty
12-644-00 Booklet maker staple car-
tridge is empty. Replace
12-183-00-
now
RAP
12-649-00 The hole punch waste
container is full. Empty
hole punch waste con-
RAP
tainer
12-649-01 The hole punch waste
container is full. Empty
Hole Punch Waste Con-
12-
tainer
12-653-00 Stapling fault. Power off
then on and notify system
administrator
12-
February 2013
2-542
Table 7 Chain 12 Status codes
Reason for Message
The booklet maker staples
are low
The booklet maker staple car-
tridge is empty
The booklet maker staple car-
tridge is empty
The booklet maker staple car-
tridge is empty and HVF fin-
isher front door open
The hole punch chad bin is
full and needs emptying.
(LCSS)
The hole punch chad bin is
full and needs emptying.
(HVF)
Stapling disabled, out of ser-
vice. (LCSS)
ColorQube® 9303 Family
Reference / Action
The booklet maker
staple cartridge sup-
plies are low. Re-
order staple car-
tridge, PL 12.185 Item
8
The booklet maker
staple cartridge is
empty. Follow the
instructions at the
printer to load a new
staple cartridge, PL
12.185 Item 8. Print-
ing can continue, but
stapled booklet mak-
ing is unavailable
Install a new booklet
maker staple cartridge
The booklet maker
staple cartridge is
empty. User interven-
tion is required to
install a new booklet
maker staple car-
tridge, PL 12.185 Item
8. Printing and copy-
ing can continue with-
out stapled booklet
making
Hole punch waste
container is full, jobs
requesting hole
punching will be held.
Empty the chad bin
Hole punch waste
container is full, jobs
requesting hole
punching will be held.
Empty the chad bin
Perform the 12-371-
00-110, 12-372-00-
110, 12-378-00-110
RAP