Xerox ColorQube 9303 Series Service Manual page 362

82-502-00, 82-503-00 Horizontal Transport Motor M6
Failure RAP
82-502-00 Transport motor M6 over current fault.
82-503-00 Transport motor M6 stalled.
Initial Actions
WARNING
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to GP 14. Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
• Check for obstructions in the horizontal paper path.
• Check the nip rolls on the horizontal paper path,
Procedure
Clean the pre transfix sensor 20, PL 88.10 Item 12
Y N
Perform SCP 5 Final Actions.
Enter dC330 code 89-006 pre transfix sensor (20), Q89-006. Press Start. Manually actuate the
sensor. The display changes.
Y N
Go to WD 8.6. Check pre transfix sensor 20, Q89-006. Refer to:
• REP 89.1 Registration / preheat Assembly and Lower Platelet Assembly
• GP 11 How to Check a Sensor.
• PJ5, Registration / preheat IF PWB.
• 01D +5V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Pre transfix sensor (20), PL 88.10 Item
• Registration / preheat IF PWB,
• Media path PWB, PL 1.15 Item
Enter dC330 code 82-003 horizontal transport motor (M6), MOT82-003. Press Start. The
motor runs.
Y N
Go to WD 8.5. Check horizontal transport motor (M6), MOT82-003. Refer to:
• GP 10 How to Check a Motor.
• PJ905, Media path driver PWB.
• 01D +5V Distribution RAP.
• 01J +50V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Horizontal transport motor (M6),
• Media path driver PWB, PL 1.15 Item
A
Status Indicator RAPs
82-502-00, 82-503-00
PL 82.15 Item 10.
and refer to GP 27. The fault remains.
12.
PL 88.10 Item 10.
5.
PL 82.15 Item 9.
5.
A
Enter dC140 Analog Monitor. Select 82-102 horizontal transport motor encoder (M6). Press
Start. The number of ticks (i.e. 36 ticks) will flash on the display and then return to show 0 ticks.
Repeat by selecting stop and then start on the popup menu, the number only remains for a few
seconds. The number of ticks is displayed.
Y N
Go to WD 8.5. Check horizontal transport motor (M6), MOT82-003 and the encoder wire
harness. Refer to:
• GP 10 How to Check a Motor.
• PJ905, Media path driver
• 01D +5V Distribution RAP.
• 01J +50V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Horizontal transport motor (M6),
• Media path driver PWB,
Check the following:
• Check the wiring for damage,
• The bearing, shaft and rolls on the horizontal paper path,
• Check the drive belt and drive gears on the horizontal paper path,
If necessary, install new components:
• Transport rolls, PL 82.15 Item
• Transport drive belts, PL 82.15 Item
• Drive belt, PL 82.15 Item 8.
• Drive gears, PL 82.15.
February 2013
2-338
PWB.
PL 82.15 Item 9.
PL 1.15 Item 5.
REP 1.1.
PL 82.15 Item
PL 82.15.
10.
7.
ColorQube® 9303 Family
14.