Table of Contents
Advertisement
93-592-00 Head 3 yellow reservoir level sense open circuit
93-593-00 Head 4 black reservoir level sense open circuit
93-594-00 Head 4 magenta reservoir level sense open circuit
93-595-00 Head 4 cyan reservoir level sense open circuit
93-596-00 Head 4 yellow reservoir level sense open circuit
93-597-00 Head 1 black reservoir level sense short circuit
93-598-00 Head 1 magenta reservoir level sense short circuit
93-599-00 Head 1 cyan reservoir level sense short circuit
93-800-00 Head 1 yellow reservoir level sense short circuit
93-801-00 Head 2 black reservoir level sense short circuit
93-802-00 Head 2 magenta reservoir level sense short circuit
93-803-00 Head 2 cyan reservoir level sense short circuit
93-804-00 Head 2 yellow reservoir level sense short circuit
93-805-00 Head 3 black reservoir level sense short circuit
93-806-00 Head 3 magenta reservoir level sense short circuit
93-807-00 Head 3 cyan reservoir level sense short circuit
93-808-00 Head 3 yellow reservoir level sense short circuit
93-809-00 Head 4 black reservoir level sense short circuit
93-810-00 Head 4 magenta reservoir level sense short circuit
93-811-00 Head 4 cyan reservoir level sense short circuit
93-812-00 Head 4 yellow reservoir level sense short circuit
Procedure
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to
GP
14. Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
Verify the fault code. Go to the relevant RAP:
•
Head 1 and head 3 faults.
–
93-549-00 to 93-552-00 and 93-557-00 to 93-560-00
Reservoir Fill Error RAP
•
Head 2 and head 4 faults.
–
93-553-00 to 93-556-00 and 93-561-00 to 93-564-00
Reservoir Fill Error RAP
Status Indicator RAPs
93-565-00 to 93-599-00 and 93-800-00 to 93-812-00, 93-
WARNING
Printheads 1 and 3 Printhead
Printheads 2 and 4 Printhead
93-813-00 to 93-820-00 Ink Melt Reservoir Level Sense
Failure RAP
93-813-00 Black melt reservoir level sense open circuit
93-814-00 Magenta melt reservoir level sense open circuit
93-815-00 Cyan melt reservoir level sense open circuit
93-816-00 Yellow melt reservoir level sense open circuit
93-817-00 Black melt reservoir level sense short circuit
93-818-00 Magenta melt reservoir level sense short circuit
93-819-00 Cyan melt reservoir level sense short circuit
93-820-00 Yellow melt reservoir level sense short circuit
Procedure
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to
death or injury. Moving parts can cause injury.
1.
If the ink sticks are not in contact with the melt plate correct the ink stick jam. Install new
components as necessary
2.
Go to
WD 9.9
and
WD
9.16. Check the wiring between the ink level sensors, the solenoid
patch PWB and the marking unit driver PWB.
Refer to:
•
P/J101,
Marking unit driver PWB
•
P/J380, P/J760, P/J780
•
01B
+3.3V ESTAR Distribution RAP.
•
01L
0V Distribution RAP
3.
If the sensor continues to report a fault, install a new ink melt reservoir,
4.
Install new components as necessary:
•
Ink reservoir,
PL 93.10 Item
•
Marking unit driver PWB,
February 2013
2-446
WARNING
GP
14. Disconnect the power cord. Electricity can cause
PL
93.10.
Solenoid patch PWB.
10.
PL 92.10 Item
4.
ColorQube® 9303 Family
PL 93.10 Item
10.
Advertisement
Chapters
Table of Contents
