Xerox ColorQube 9303 Series Service Manual page 196

12K-171 HVF Initialization Failure RAP
When an initialization command is received from the machine, the HVF is initialized with the
following actions:
1. The stacker tray moves down and then up.
2. The lower paddle rotates to home position.
3. The paddle unit moves up.
4. The paper pusher comes down
5. The ejector moves out.
6. The staple head moves to the rear.
7. The staple head moves back home, front.
8. The pusher moves up to home position
9. The ejector moves back into home position.
10. The pressing and support fingers come out and then move in.
11. The paddle unit moves down.
12. The paddles in the paddle unit rotate twice.
13. The HVF should now be ready to run if all these checks completed successfully.
NOTE: The HVF initialization procedure can be triggered by opening and closing the HVF front
door, or by raising and lowering the top tray. When this is done the tray will not lower com-
pletely, but will adjust its position.
The booklet maker is initialized as follows:
1. The BM tampers are driven to their home position, unless already home.
2. The BM backstop is driven to the home position, unless already home.
3. The BM crease roll gate is driven to the home position, unless already home.
4. The BM crease blade is driven to the home position, unless already home.
5. The BM staple heads are driven to their home position, unless already home.
Initial Actions
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to GP 14. Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
Open the HVF front door. Cheat the front door interlock switch. Fully pull out the BM module
Procedure
If the initialization sequence fails to place any unit at the home position, refer to the appropriate
RAPs:
• Front tamper not at home, refer to
Tray RAP
• Rear tamper not at home, refer to
Tray RAP.
• Paddle not at home, refer to 12-024-00-171, 12-025-00-171
• Bin 1 not at home, refer to 12-460-00-171 to 12-462-00-171
• Punch not at home, refer to 12-044-00-171 to 12-047-00-171
Status Indicator RAPs
12K-171
WARNING
12-392-00-171 to 12-395-00-171 HVF Front tamper
12-396-00-171 to 12-399-00-171 HVF Rear Tamper
Paddle Roll Position RAP.
HVF Bin 1 Position RAP.
Punch head Position RAP
• Staple head not at home, refer to
and Priming RAP.
• Ejector not at home, refer to
tor Module RAP.
• The buffer motor fails to start, refer to
RAP.
• Entry feed motor 1 fails to start, refer to
RAP.
• Transport motor 2 fails to start, refer to
sor RAP.
• The booklet maker diverter solenoid fails to energizes, refer to
171, 12-190-00-171, 12-192-00-171
• The exit diverter solenoid fails to energies, refer to
Top Exit Sensor RAP.
• Either of the BM staple heads are not at the home position, refer to
411-00-171 HVF BM Stapler Unit 1 Failure RAP or
414-00-171 HVF BM Stapler Head 2 and Stapler Module RAP.
• The BM tampers are not at the home position, refer to
419-00-171, 12-420-00-171
• The BM backstop is not at the home position, refer to
BM Backstop Failure RAP.
• The BM crease roll gate is not at the home position, refer to
Crease Roll Gate Home RAP.
• The BM crease blade is not at the home position, refer to
HVF BM Creasing RAP.
February 2013
2-172
12-369-00-171 to 12-377-00-171
12-450-00-171, 12-456-00-171 to 12-459-00-171
12-141-00-171, 12-142-00-171
12-125-00-171, 12-126-00-171
12-171-00-171, 12-172-00-171
12-113-00-171, 12-114-00-
HVF BM Entry RAP.
12-171-00-171, 12-172-00-171
12-403-00-171, 12-413-00-171, 12-
12-066-00-171, 12-384-00-171, 12-
HVF BM Tamper Failure RAP.
12-065-00-171, 12-383-00-171
12-415-00-171
12-061-00-171, 12-416-00-171
ColorQube® 9303 Family
HVF stapler Position
HVF Ejec-
HVF Buffer Path
HVF Entry Sensor
HVF Top Exit Sen-
HVF
12-063-00-171, 12-
HVF
HVF BM