Table of Contents
Advertisement
Table 5 Chain 05 Status codes
Status
Code
UI Message
Reason for Message
05-578-00 Re-order document
DADH roller feeds reaches
feeder - feed roller but
near end of life limit.
DO NOT replace until
prompted
05-579-00 Replace the document
DADH roller feeds reaches
feed roller
end of life
05-585-00 Select confirm if the doc-
When status 05-579 is active
ument feeder - feed roller
and the DADH top cover is
was replaced.
opened (status 05-502)
Table 6 Chain 10 Status codes
Status
Code
UI Message
Reason for Message
10-536-00 No message
Transfix calibration
NVRAM parameters are
reset.
Table 7 Chain 12 Status codes
Status
Code
UI Message
12-410-00 No message
12-411-00 The current job exceeds
the tray capacity, you will
be prompted to empty the
tray
12-564-00 The finisher front door is
open
12-564-01 The finisher front door is
open
12-564-02 The finisher front door is
open
Status Indicator RAPs
OF 4a
Reference / Action
Order new DADH feed
roll assembly,
Item 1
Install new DADH feed
roll assembly,
Item
1.
Select confirm if the
document feeder - feed
roller was replaced
Reference / Action
Refer to
OF 12
Service Code
RAP
Reason for Message
Reference / Action
PTU selected whilst marking
Pressing the Pause to
job is running
Unload button will
cancel this request
Copy Job will exceed the out-
Empty the tray
put destination's capacity
The finisher front door is open
Close the finisher
(LCSS)
front door
The finisher front door is open
Close the finisher
(HVF - all variants)
front door
The finisher front door is open
Close the finisher
(HVF with tri-folder)
front door
Status
Code
UI Message
12-579-00 Hole punching not avail-
PL 5.15
able. Power off then on
and notify system admin-
istrator
PL 5.15
12-600-00 Finisher is not docked.
Re-dock finisher now
12-600-01 Finisher is not docked.
Re-dock finisher now
12-600-02 Finisher is not docked.
Re-dock finisher now
12-601-00 Close the finisher top tray LCSS finisher top cover is
12-602-00 Close finisher top cover
12-606-00 Close finisher top cover
12-607-00 Close the finisher folder
top cover
12-608-00 Close the finisher folder
front door
12-609-00 Close finisher inserter left
side door
12-610-00 Paper jam in the finisher
February 2013
2-540
Table 7 Chain 12 Status codes
Reason for Message
Hole punching is not available Check that the hole
The finisher unit (LCSS) is not
correctly docked. Printing has
stopped
The finisher unit (HVF without
tri-folder) is not correctly
docked. Printing has stopped
The finisher unit (HVF with tri-
folder) is not correctly docked.
Printing has stopped
open (cover over output tray)
The finisher top cover is open Close the finisher top
The inserter top cover is open Close the inserter top
The tri-folder top cover is
open (HVF with tri-folder)
The tri-folder unit front door is
open (HVF with trifolder)
The inserter left cover is open
(HVF without Tri-folder)
Paper is detected over the
entry sensor (LCSS)
ColorQube® 9303 Family
Reference / Action
punch unit is cor-
rectly installed. Switch
the machine off then
on,
GP
14. If the prob-
lem persists, perform
the
12-043-00-110,
12-046-00-110
RAP
for LCSS,
12-044-00-
171 to 12-047-00-171
RAP for HVF
Dock the output mod-
ule. If the problem
persists, perform the
12-310-00-110, 12-
312-00-110, 12-313-
00-110
RAP
Dock the output mod-
ule. If the problem
persists, perform the
12-310-00-171, 12-
312-00-171, 12-313-
00-171
RAP
Dock the output mod-
ule. If the problem
persists, perform the
12-310-00-171, 12-
312-00-171, 12-313-
00-171
RAP
Close the top cover
cover.
cover
Close the tri-folder top
cover
Close the tri-folder
front door
Close the inserter left
cover
Clear the paper jam. If
the problem persists,
perform the
12-199-
00-110
RAP
Advertisement
Chapters
Table of Contents
