Xerox ColorQube 9303 Series Service Manual page 161

Y N
Go to WD 12.19 and WD 12.20. Check the wiring and repair as necessary,
Check the tri-folder top cover interlock sensor, Q12-210. Refer to:
• GP 11 How to Check a Sensor.
• 12A-171 HVF Power Distribution RAP.
• 01L 0V Distribution RAP
Install new components as necessary:
• Tri-folder top cover interlock sensor,
• Tri-folder PWB, PL 12.205 Item
• BM PWB, PL 12.175 Item 10.
Perform SCP 5 Final Actions.
Tri-folder top cover
interlock switch
Figure 1 Component location
ColorQube® 9303 Family
PL 12.200 Item 10.
16.
Tri-folder top cover
interlock sensor
Q12-210
Tri-folder front door
interlock switch, S12-
209
12-367-00-171, 12-368-00-171, 12-380-00-171 HVF Punch
REP 1.1.
Unit Paper Edge Detect RAP
12-367-00-171 The punch unit failed to detect the edge of the A4 LE feed paper.
12-368-00-171 The punch unit failed to detect the edge of the 8.5"x 11" SE feed paper.
12-380-00-171 The punch unit failed to detect the edge of the 8.5"x11" LE feed paper.
Initial Actions
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to
death or injury. Moving parts can cause injury.
• Check that the paper path through the punch is clear,
• Check the punch module is seated at the rear or the machine.
• Check that a ColorQube punch unit is installed. A ColorQube unit has 3 sensors on the
unit, Figure 1.
Procedure
Figure 1. Punch sensor 1, Q12-078 detects 8.5"x11" LE feed paper. Punch sensor 2, Q12-075
detects 8.5"x11" SE feed paper. Punch sensor 3, Q12-076 detects A4 LE feed paper.
Enter dC330, enter the relevant code then actuate and check each of the three punch sensors.
• code 12-078 for punch sensor 1.
• code 12-075 for punch sensor 2.
• code 12-076 for punch sensor 3.
The display changes.
Y N
Go to WD 12.12 for punch sensor 1 and
wiring and repair as necessary,
• GP 11 How to Check a Sensor.
• 12A-171 HVF Power Distribution RAP.
• 01L 0V Distribution RAP
Install new components as necessary:
• Punch sensor 1,
• Punch sensor 2,
• Punch sensor 3,
• HVF PWB, PL 12.140 Item
Enter dC330, code 12-223 transport motor 1, to check that the motor runs. The motor runs.
Y N
Go to WD 12.7. Check the wiring and repair as necessary,
Refer to:
• GP 10 How to Check a Motor.
• 12A-171 HVF Power Distribution RAP.
• 01L 0V Distribution RAP
A
February 2013
12-317-00-171, 12-318-00-171, 12-367-00-171, 12-
2-137
WARNING
GP 14. Disconnect the power cord. Electricity can cause
Figure 1.
WD 12.24 for punch sensors 2 & 3. Check the
REP 1.1. Refer to:
PL 12.125 Item 17.
PL 12.125 Item 17.
PL 12.125 Item 17.
2.
REP 1.1. Check MOT12-223.
Status Indicator RAPs