Xerox ColorQube 9303 Series Service Manual page 347

A
• PJ504, tray 5 control PWB.
• 01H +24V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Tray 5 stack upper limit switch,
• Tray 5 control PWB, PL 75.68 Item
Enter dC140 code 75-015 tray 5 elevator encoder sensor, Q75-015,
Start. Manually lift the motor to actuate the sensor. The display changes.
Y N
Refer to WD 7.2. Check tray 5 elevator encoder, Q75-015. Refer to:
• GP 11 How to Check a Sensor.
• PJ506, tray 5 control PWB.
• 01D +5V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Elevator encoder sensor, PL 75.68 Item
• Tray 5 control PWB, PL 75.68 Item
Enter dC330 code 75-019 tray 5 elevator motor (up), MOT75-019,
Start. The motor runs.
Y N
Refer to WD 7.1. Check tray 5 elevator motor, MOT75-019. Refer to:
• GP 10 How to Check a Motor.
• PJ504, tray 5 control PWB.
• 01H +24V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Tray 5 elevator motor, PL 75.68 Item
• Tray 5 control PWB, PL 75.68 Item
• Media path driver PWB, PL 1.15 Item
The tray 5 elevator motor is operating correctly. Perform
ColorQube® 9303 Family
PL 75.68 Item 12.
8.
PL 75.68 Item
5.
8.
PL 75.68 Item
4.
8.
5.
SCP 5 Final Actions.
75-213-00, 75-216-00 Tray 5 Elevate Down Failure RAP
75-213-00 Tray 5 encoder failure on lower. A signal was not detected by the encoder when the
elevator motor was driving down.
75-216-00 Tray 5 lower failure. The tray 5 stack down sensor did not actuate in expected time
during lower.
Initial Actions
5. Press
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to
death or injury. Moving parts can cause injury.
• Check for obstructions in the tray.
• Check that the door latches correctly.
• Open and close the tray 5 door. If the tray moves down, check for intermittent failures.
Refer to WD 7.1 and WD
Procedure
Enter dC330 code 75-010 tray 5 door switch, S75-010,
4. Press
toggle the door interlock switch. The display changes.
Y N
Refer to WD 7.2. Check tray 5 door interlock switch, S75-010. Refer to:
• GP 13 How to Check a Switch.
• PJ507, tray 5 control
• 01D +5V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Tray 5 door interlock switch,
• Tray 5 control PWB,
Enter dC330 code 75-012 tray 5 down sensor, Q75-012,
ally actuate the stack down sensor actuator. The display changes.
Y N
Refer to WD 7.2. Check tray 5 down sensor, Q75-012. Refer to:
• GP 11 How to Check a Sensor.
• PJ505, tray 5 control
• 01D +5V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Tray 5 down sensor,
• Tray 5 control PWB,
Check the voltage on PJ504 pin 6 on the
tray 5 down limit switch (S75-415),
February 2013
75-212-00, 75-215-00, 75-213-00, 75-216-00
2-323
WARNING
GP 14. Disconnect the power cord. Electricity can cause
7.2.
PL 75.60 Item 6. Press Start. Manually
PWB.
PL 75.60 Item 6.
PL 75.68 Item 8.
PL 75.68 Item
PWB.
PL 75.68 Item 9.
PL 75.68 Item 8.
tray 5 control PWB, WD 7.1. Manually actuate the
PL 75.70 Item 2, on the paper tray. The voltage changes.
Status Indicator RAPs
9. Press Start. Manu-