Xerox ColorQube 9303 Series Service Manual page 342

73A Tray 3 Out of Paper RAP
Use this RAP when the copier display instructs the operator to add paper to tray 3 when the
tray is not empty.
Initial Actions
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to GP 14. Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
• Check the position of the tray empty sensor,
• Clean the tray empty sensor.
Procedure
Enter dC330 code 73-201 tray 3 empty sensor,
Use a piece of paper to manually actuate the tray empty sensor with a piece of paper. The
display changes.
Y N
Refer to WD 7.4. Check tray 3 empty sensor, Q73-201. Refer to:
• GP 11 How to Check a Sensor.
• PJ953, 3 tray module PWB.
• 01D +5V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Tray 3 empty sensor, PL 81.30 Item
• 3 tray module PWB, PL 73.16 Item
• Media path driver PWB, PL 1.15 Item
Enter dC330 code 73-383 tray 3 stack height sensor, Q73-383,
Pull out tray 3. Manually actuate the stack height sensor. The display changes
Y N
Refer to WD 7.4. Check tray 3 stack height sensor, Q73-383. Refer to:
• GP 11 How to Check a Sensor.
• PJ953, 3 tray module PWB.
• 01D +5V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Tray 3 stack height sensor, PL 81.30 Item
• 3 tray module PWB, PL 73.16 Item
• Media path driver PWB, PL 1.15 Item
The fault may be intermittent. Perform the following:
• Check that the base plate in tray 3 is located correctly.
• Check that PJ958 harness is connected correctly and not damaged. Refer to
Tray 3 Paper Feed Assembly. Repair the wiring as necessary,
Status Indicator RAPs
73A, 74-101-00, 74-160-00 to 74-161-00
WARNING
PL 81.30 Item 19.
PL 81.30 Item 19. Press Start.
19.
4.
5.
PL 81.30 Item 17. Press Start.
17.
4.
5.
REP 1.1.
74-101-00, 74-160-00 to 74-161-00 Bypass Tray 4 Mis-Feed RAP
74-101-00 Tray 4 misfeed jam. The feed sensor did not actuate in the correct time after paper
feed from the bypass tray
74-160-00 Extra pick retry O.K.
74-161-00 Extra pick retry fail.
Initial Actions
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to
death or injury. Moving parts can cause injury.
• Check the condition of the paper in tray. Refer to
• Check the paper guides are set correctly.
• Check the condition of the bypass tray 4 feed, nudger and retard rolls. Use a cloth dampened
with water to clean the rolls,
Item 26.
• Go to dC135 CRU/HFSI Status. Check the count of the tray 4 bypass feed roll set. If the
count is near end of life, install a new tray 4 feed roll kit,
Procedure
Enter dC330 code 74-406 bypass feed sensor, Q74-406,
ally actuate the bypass feed sensor. The display changes.
Y N
Refer to WD 8.3. Check bypass feed sensor, Q74-406. Refer to:
• GP 11 How to Check a Sensor.
• PJ405, Media path driver
• 01C +3.3V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Bypass feed sensor,
• Media path driver PWB,
Enter dC330 code 74-420 bypass feed motor (M7), MOT74-420,
nudger assembly. Press Start. The motor runs.
Y N
Refer to WD 8.3. Check bypass feed motor (M7), MOT74-420. Refer to:
• GP 10 How to Check a Motor.
• PJ405, Media path driver PWB.
• 01H +24V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Bypass module,
• Media path driver PWB,
REP 81.2 Perform the following:
• Check the feed roll assembly,
• Check the takeaway nip rolls,
Install new components as necessary.
February 2013
2-318
WARNING
GP 14. Disconnect the power cord. Electricity can cause
GP 20.
GP 27. If necessary, install a new tray 4 feed roll kit,
PL 31.11 Item
PL 74.10 Item
PWB.
PL 74.10 Item 19.
PL 1.15 Item 5.
PL 74.10 Item
PL 74.10 Item 1.
PL 1.15 Item 5.
PL 74.10 Item 14.
PL 70.30 Item 12.
PL 31.11
26.
19. Press Start. Manu-
2. Support the
ColorQube® 9303 Family