Xerox ColorQube 9303 Series Service Manual page 392

91-523-00 to 91-558-00, 91-664-00 to 91-667-00, 91-800-00
to 91-803-00, 91-856-00 to 91-859-00 Printhead Thermal
Error RAP
91-523-00 Printhead 1 Left Jet Heater is Too Hot
91-524-00 Printhead 2 Left Jet Heater is Too Hot
91-525-00 Printhead 3 Left Jet Heater is Too Hot
91-526-00 Printhead 4 Left Jet Heater is Too Hot
91-527-00 Printhead 1 Left Jet Heater is Too Slow
91-528-00 Printhead 2 Left Jet Heater is Too Slow
91-529-00 Printhead 3 Left Jet Heater is Too Slow
91-530-00 Printhead 4 Left Jet Heater is Too Slow
91-531-00 Printhead 1 Left Jet Thermistor value inconsistent with expected value.
91-532-00 Printhead 2 Left Jet Thermistor value inconsistent with expected value.
91-533-00 Printhead 3 Left Jet Thermistor value inconsistent with expected value.
91-534-00 Printhead 4 Left Jet Thermistor value inconsistent with expected value.
91-535-00 Printhead 1 Right Jet Heater is Too Hot
91-536-00 Printhead 2 Right Jet Heater is Too Hot
91-537-00 Printhead 3 Right Jet Heater is Too Hot
91-538-00 Printhead 4 Right Jet Heater is Too Hot
91-539-00 Printhead 1 Right Jet Heater is Too Slow
91-540-00 Printhead 2 Right Jet Heater is Too Slow
91-541-00 Printhead 3 Right Jet Heater is Too Slow
91-542-00 Printhead 4 Right Jet Heater is Too Slow
91-543-00 Printhead 1 Right Jet Thermistor value inconsistent with expected value.
91-544-00 Printhead 2 Right Jet Thermistor value inconsistent with expected value.
91-545-00 Printhead 3 Right Jet Thermistor value inconsistent with expected value.
91-546-00 Printhead 4 Right Jet Thermistor value inconsistent with expected value.
91-547-00 Printhead 1 Reservoir Heater Too Hot
91-548-00 Printhead 2 Reservoir Heater Too Hot
91-549-00 Printhead 3 Reservoir Heater Too Hot
91-550-00 Printhead 4 Reservoir Heater Too Hot
91-551-00 Printhead 1 Reservoir Heater Too Slow
91-552-00 Printhead 2 Reservoir Heater Too Slow
91-553-00 Printhead 3 Reservoir Heater Too Slow
91-554-00 Printhead 4 Reservoir Heater Too Slow
Status Indicator RAPs
91-523-00 to 91-558-00, 91-664-00 to 91-667-00, 91-
91-555-00 Printhead 1 Reservoir Thermistor value inconsistent with expected value.
91-556-00 Printhead 2 Reservoir Thermistor value inconsistent with expected value.
91-557-00 Printhead 3 Reservoir Thermistor value inconsistent with expected value.
91-558-00 Printhead 4 Reservoir Thermistor value inconsistent with expected value.
91-664-00 Printhead 1 thermal failure.
91-665-00 Printhead 2 thermal failure.
91-666-00 Printhead 3 thermal failure.
91-667-00 Printhead 4 thermal failure.
91-800-00 Head 1 thermal glitch.
91-801-00 Head 2 thermal glitch.
91-802-00 Head 3 thermal glitch.
91-803-00 Head 4 thermal glitch.
91-856-00 Head 1 thermal persistent glitch.
91-857-00 Head 2 thermal persistent glitch.
91-858-00 Head 3 thermal persistent glitch.
91-859-00 Head 4 thermal persistent glitch.
Initial Actions
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to
death or injury. Moving parts can cause injury.
Do not touch the exposed face of the printheads. Surface contamination or minor damage can
destroy the printhead. Printheads must only be cleaned by a purge cycle.
Use care when opening the marking unit drawer when hot. Ink can spill from the ink reservoir
located at the back of the drawer if opened with too much force. Ink cross-color contamination
could also occur.
The video cable (striped and labeled A,
labeled B, PL 92.10 Item 8) should not be interchanged at the printhead connectors. Damage
to the printhead and IME controller PWB will occur if the cables are installed incorrectly
• Check all 3 wiring harness leading to the indicated printhead. Focus on areas above and
behind the umbilicals. Ensure each harness is securely and correctly seated, refer to
28.
Procedure
Check for damage to the cables connecting each printhead. The wiring is good.
Y N
Install new cables as necessary,
A
February 2013
2-368
WARNING
GP 14. Disconnect the power cord. Electricity can cause
CAUTION
CAUTION
CAUTION
PL 92.10 Item 7) and the wave amp cable (white and
PL 92.10.
ColorQube® 9303 Family
GP