Table of Contents
Advertisement
12-191-00-171, 12-193-00-171, 12-194-00-171, 12-196-00-
171 Inserter Paper Jam RAP
12-191-00-171 The leading edge is late arriving at the inserter standby sensor.
12-193-00-171 The trailing edge is late leaving the inserter standby sensor.
12-194-00-171 The leading edge is late arriving at the inserter pickup sensor.
12-196-00-171 The trailing edge is late leaving the inserter pickup sensor.
Fault code 12-191-00 may also be generated where a fault in the inserter causes jamming in
the IME.
Initial Actions
WARNING
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to
GP
14. Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
•
Check for a jam or other obstruction in the inserter.
•
Check the inserter for damage.
•
Check the condition of the inserter feed rolls. Use a cloth dampened with water to clean
the rolls. If necessary, install a new inserter pickup assembly,
•
Go to
dC135
CRU/HFSI Status. Check the count of the inserter feed roller set. If the count
is near end of life, install a new inserter pickup assembly,
Procedure
Enter
dC330
code 12-315. Manually actuate the inserter pickup sensor, Q12-315,
The display changes.
Y
N
Go to
WD
12.14,
WD 12.21
and
WD 12.22
Refer to:
•
GP 11
How to Check a Sensor.
•
12A-171
HVF Power Distribution RAP.
•
01L
0V Distribution RAP
Install new components as necessary:
•
Inserter pickup sensor,
PL 12.310 Item
•
Inserter PWB,
PL 12.310 Item
9.
•
HVF PWB,
PL 12.140 Item
2.
Enter
dC330
code 12-084. Manually actuate the inserter TE sensor, Q12-084,
display changes.
Y
N
Go to
WD 12.13
and
WD
12.21. Check Q12-084.
Refer to:
•
GP 11
How to Check a Sensor.
•
12A-171
HVF Power Distribution RAP.
A
Status Indicator RAPs
12-191-00-171, 12-193-00-171, 12-194-00-171, 12-196-
PL 12.310 Item
1.
PL 12.310 Item
1.
Figure
Check Q12-315.
10.
Figure
1. The
February 2013
A
•
01L
0V Distribution RAP
Install new components as necessary:
•
Inserter TE sensor,
PL 12.310 Item
•
Inserter PWB,
PL 12.310 Item
•
HVF PWB,
PL 12.140 Item
Enter
dC330
code 12-083. Manually actuate the inserter LE sensor, Q12-083,
display changes.
Y
N
Go to
WD 12.13
and
WD
12.21. Check Q12-083.
Refer to:
•
GP 11
How to Check a Sensor.
•
12A-171
HVF Power Distribution RAP.
•
01L
0V Distribution RAP
Install new components as necessary:
•
Inserter LE sensor,
PL 12.310 Item
•
Inserter PWB,
PL 12.310 Item
•
HVF PWB,
PL 12.140 Item
Enter
dC330
code 12-316. Manually actuate the inserter acceleration sensor Q12-316,
1. The display changes.
Y
N
Go to
WD 12.13, WD 12.21
and
Refer to:
•
GP 11
How to Check a Sensor.
•
12A-171
HVF Power Distribution RAP.
•
01L
0V Distribution RAP
1.
Install new components as necessary:
•
Inserter acceleration sensor,
•
Inserter PWB,
PL 12.310 Item
•
HVF PWB,
PL 12.140 Item
Enter
dC330
code 12-320. Manually actuate the inserter standby sensor Q12-320. The
age changes.
Y
N
Go to
WD
12.14. Check the sensor.
Refer to:
•
GP 11
How to Check a Sensor.
•
12A-171
HVF Power Distribution RAP.
•
01L
0V Distribution RAP
Install new components as necessary:
•
Inserter standby sensor,
•
HVF PWB,
PL 12.140 Item
Enter
dC330
code 12-260 to energize the inserter clutch CL12-260. The clutch energizes.
Y
N
Go to
WD
12.14,
WD 12.21
and
B
2-130
11.
9.
2.
11.
9.
2.
WD
12.22. Check the sensor.
PL 12.300 Item
10.
9.
2.
PL 12.135 Item
2.
2.
WD
12.22. Check CL 12-260.
ColorQube® 9303 Family
Figure
1. The
Figure
volt-
Advertisement
Chapters
Table of Contents
