Xerox ColorQube 9303 Series Service Manual page 113

12-371-00-110, 12-372-00-110, 12-378-00-110 Staple Head
Unit Movement Failure RAP
12-371-00-110 The staple head unit fails to move.
12-372-00-110 The staple head unit is not at the home position.
12-378-00-110 The staple head unit is not indexed correctly.
NOTE: The home position is when the staple head unit is at the corner stapling position (fully
to the front of the LCSS and rotated through 45 degrees).
Initial Actions
WARNING
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to GP 14. Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
WARNING
Take care not to topple the LCSS. The LCSS is unstable when undocked from the
machine. Do not show the customer how to undock the LCSS.
• Check the LCSS PWB DIP switch settings, refer to
tings RAP.
• Un-dock the LCSS from the machine,
the right, manually move the stapler unit along the full length of the track using the green
thumb-wheel. Check the home sensor flag and the two dual position flags for damage,
see NOTE. Check for damage or obstructions that would prevent the stapling unit from
moving. If necessary, install a new staple head unit,
traverse assembly, PL 12.55 Item 1.
NOTE: For dual position stapling, the SU1 front index sensor uses two flags.
• Dock the LCSS to the machine.
Procedure
NOTE: All LCSS interlocks must be made to supply +24V to the motors.
NOTE: With reference to WD 12.3, component control codes;
Code 12-249 increments the stapling unit motor in the forward direction.
Code 12-045 increments the stapling unit motor in the reverse direction.
Code 12-250 cycles the stapling unit between home, first and second stapling positions.
Enter dC330 code 12-235 to move the ejector assembly fully to the right,
Enter code 12-250. The stapling unit cycles back and forth along the track.
Y N
Go to WD 12.3. Check the SU1 motor, MOT12-249.
Refer to:
• 12G-110 LCSS PWB Damage RAP.
• GP 10, How to Check a Motor.
• P/J308, LCSS PWB.
A
ColorQube® 9303 Family
12F-110 LCSS PWB DIP Switch Set-
REP 12.13-110, move the ejector assembly fully to
PL 12.55 Item 5 or a new stapler
PL 12.50 Item
A
• Figure 1, Component location.
• 12D-110 LCSS Power Distribution RAP.
• 01L 0V Distribution RAP
Install new components as necessary:
• Stapler traverse assembly,
• LCSS PWB, PL 12.75 Item
Enter dC330 code 12-135. Actuate the stapler home sensor Q12-135 by moving the stapler
unit to and from the home position, using the green thumb-wheel. The display changes.
Y N
Go to WD 12.3. Check Q12-135.
Refer to:
• 12G-110 LCSS PWB Damage RAP.
• GP 11. How to check a sensor.
• Figure 1.
• P/J308, LCSS PWB.
• 12D-110 LCSS Power Distribution RAP.
• 01L 0V Distribution RAP
Install new components as necessary:
• Stapler home sensor,
• LCSS PWB, PL 12.75 Item
Enter dC330 code 12-235 to move the ejector assembly fully to the right. Enter code 12-168.
Actuate the stapler index sensor Q12-168 by moving the stapler unit to and from the flag posi-
tion (approximately 115 mm (4.5 inches) from the front of the track), using the green thumb-
wheel. The display changes.
Y N
Go to WD 12.2. Check Q12-201.
Refer to:
• 12G-110 LCSS PWB Damage RAP.
• GP 11 How to Check a Sensor.
• P/J308, LCSS PWB.
• 12D-110 LCSS Power Distribution RAP.
• 01L 0V Distribution RAP
Install new components as necessary:
• Stapler index sensor,
• LCSS PWB, PL 12.75 Item
1. Perform SCP 5 Final Actions.
February 2013
12-371-00-110, 12-372-00-110, 12-378-00-110
2-89
PL 12.55 Item 1.
1.
PL 12.55 Item 3.
1.
PL 12.55 Item 3.
1.
Status Indicator RAPs