Xerox ColorQube 9303 Series Service Manual page 137

12-066-00-171, 12-384-00-171, 12-419-00-171, 12-420-00-
171 HVF BM Tamper Fault RAP
12-066-00-171 The HVF BM tamper has failed to clear the home sensor.
12-384-00-171 The HVF BM tamper is not at the home sensor.
12-419-00-171 The HVF BM tamper home fault.
12-420-00-171 The HVF BM tamper move fault.
Initial Actions
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to GP 14. Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
• Check for a jam or other obstruction that could prevent the tamper mechanism from mov-
ing.
• Check for damaged tamper components,
Procedure
Enter dC330 code 12-205. Actuate the BM tamper 1 home sensor, Q12-205,
1. The display changes.
Y N
Go to WD 12.18. Check Q12-205
Refer to:
• GP 11 How to Check a Sensor.
• 12A-171 HVF Power Distribution RAP.
• 01L 0V Distribution RAP
Install new components as necessary:
• BM PWB, PL 12.175 Item 10.
• BM tamper 1 home sensor, PL 12.155 Item
Enter dC330, code 12-256, to run the BM tamper 1 motor, MOT12-256,
The motor runs.
Y N
Go to WD 12.17. Check MOT12-256.
Refer to:
• GP 10 How to Check a Motor.
• 12A-171 HVF Power Distribution RAP.
• 01L 0V Distribution RAP
Install new components as necessary:
• BM PWB, PL 12.175 Item 10.
• BM tamper 1 motor, PL 12.155 Item
The fault may be intermittent, check for damaged wiring or bad connectors,
sary install new components:
• BM tamper 1 home sensor, PL 12.155 Item
• BM tamper 1 motor, PL 12.155 Item
• BM PWB, PL 12.175 Item 10.
ColorQube® 9303 Family
WARNING
PL 12.155.
PL 12.155 Item
1.
PL 12.155 Item
3.
REP
1.
3.
12-083-00-171, 12-440-00-171 to 12-444-00-171 HVF Paper
Pusher Fault RAP
12-083-00-171 The paper pusher motor has stalled.
12-440-00-171 The paper pusher has failed to return to the home, (upper) position.
12-441-00-171 The paper pusher has failed to move from the home, (upper) position.
12-442-00-171 The paper pusher has failed to return to the away, (lower) position.
12-443-00-171 The paper pusher has failed to move from the away, (lower) position.
12-444-00-171 The stapler gate safety switch has failed.
Initial Actions
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to
death or injury. Moving parts can cause injury.
• Check for a jam or other obstruction that could prevent the paper pusher from moving.
• Check for damaged paper pusher components.
Procedure
Enter dC330, code 12-265 to run the paper pusher motor, MOT12-265,
The motor runs.
Y N
Go to WD 12.10. Check MOT12-265
Refer to:
• GP 10 How to Check a Motor.
• 12A-171 HVF Power Distribution RAP
3.
• 01L 0V Distribution RAP
Install new components as necessary:
• Paper pusher motor,
• HVF PWB,
Go to WD 12.11. Check the stapler gate safety switch S12-319.
Refer to:
• GP 13 How to check a switch.
• P/J304, HVF PWB,
• 12A-171 HVF Power Distribution RAP
• 01L 0V Distribution RAP
The switch is good.
1.1. If neces-
Y N
Install new components as necessary.
• Sensor assembly,
• HVF PWB PL 12.140 Item
A
February 2013
12-066-00-171, 12-384-00-171, 12-419-00-171, 12-
2-113
WARNING
GP 14. Disconnect the power cord. Electricity can cause
PL 12.115 Item 13.
PL 12.140 Item 2.
PL 12.140 Item 2.
PL 12.115 Item 22.
2.
PL 12.115 Item 13.
Status Indicator RAPs