Xerox ColorQube 9303 Series Service Manual page 379

89-531-00 to 89-545-00 Registration Process Error RAP
89-531-00 The registration sensor (10) failed to detect the leading edge.
89-532-00 The registration sensor (10) timed out or failed to complete normally.
89-533-00 The registration sensor (10) generated a floating point exception.
89-534-00 The registration sensor (10) scan failed.
89-540-00 Sensor 10 post registration processing failure.
89-541-00 Sensor 10 post processing leading edge not detected.
89-542-00 Sensor 10 post processing lateral edge not detected.
89-543-00 Sensor 10 post processing leading edge error.
89-544-00 Sensor 10 post processing lateral edge error.
89-545-00 Sensor 10 post processing leading edge crossing too small.
Initial Actions
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to GP 14. Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury
• Check for damage or debris that restricts movement of the assembly.
• Check for dust or media debris around the registration scan bar.
Procedure
Enter dC715 Active registration control and disable registration control. Enter
Smears and run the routine. The pages exit the registration / preheat assembly.
Y N
Go to the 89-110-00 to 89-113-00, 89-129-00
Install a new registration / preheat assembly,
NOTE: Calibration of the registration / preheat assembly, dC625, is only required when:
• The registration / preheat assembly is removed or replaced.
• The horizontal transport assembly is removed or replaced.
Calibration of the registration / preheat assembly is NOT required when:
• A printhead is replaced.
• The IOD assembly is removed or replaced.
ColorQube® 9303 Family
WARNING
dC969
Media Path Sensor 10 Failure RAP.
PL 88.10 Item 1
89-550-00, 89-551-00 Media Registration Error RAP
89-550-00 The registration sensor detected excessive skew on the incoming media.
89-551-00 The registration sensor detected excessive offset on the incoming media.
Initial Actions
• Ensure that the tray 3 paper tray guides are set correctly,
• Check and clean the vertical and horizontal transport nip rolls up to the registration / pre-
heat assembly.
• Perform dC625 Registration / preheat Calibration routine.
Procedure
Run the job from a different tray. The fault still occurs.
Y N
Check the tray from which the fault occurs and install new components as necessary.
Enter dC330 code 82-007 Nip C release solenoid, SOL83-007. Press Start. The
energizes.
Y N
Go to WD 8.1. Check SOL83-007. Refer to:
• GP 12 How to Check a Solenoid or Clutch.
• PJ303, Media path driver
• 01J +50V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Nip C release solenoid,
• Media path driver PWB,
Enter dC330 code 82-008 Nip D release solenoid, SOL83-008. Press Start. The
energizes.
Y N
Go to WD 8.3. Check SOL83-008. Refer to:
• GP 12 How to Check a Solenoid or Clutch.
Clean Ink
• PJ405, Media path driver
• 01J +50V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Nip D release solenoid,
• Media path driver PWB,
Check the vertical and horizontal transport rolls and drive belts.Install new parts as necessary.
Refer to PL 82.10 for the vertical transport and
If the error persists, install a new registration / preheat assembly
NOTE: Calibration of the registration / preheat assembly,
• The registration / preheat assembly is removed or replaced,
• The horizontal transport assembly is removed or replaced.
Calibration of the registration / preheat assembly is NOT required when:
• A printhead is replaced.
• The IOD assembly is removed or replaced.
February 2013
89-531-00 to 89-545-00, 89-550-00, 89-551-00
2-355
ADJ 73.1.
PWB.
PL 82.15 Item 4.
PL 1.15 Item 5.
PWB.
PL 70.30 Item 13.
PL 1.15 Item 5.
PL 82.15 for the horizontal transport.
PL 88.10 Item
dC625 is only required when:
Status Indicator RAPs
solenoid
solenoid
1.