Xerox ColorQube 9303 Series Service Manual page 374

A
Enter dC330 code 82-003 Horizontal transport motor (M6) (forward), MOT82-003. Press Start.
The motor runs.
Y N
Go to WD 8.5. Check horizontal transport motor (M6), MOT82-003. Refer to:
• GP 10 How to Check a Motor.
• PJ905, Media path driver PWB.
• 01D +5V Distribution RAP.
• 01J +50V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Horizontal transport motor (M6),
• Media path driver PWB, PL 1.15 Item
The horizontal transport rolls rotate.
Y N
Check the drive belt and drive gears on the horizontal transport,
If necessary, install new components:
• Transport rolls, PL 82.15.
• Drive belts, PL 82.15.
• Drive gears, PL 82.15.
Enter dC140 Analog Monitor. Select 82-102 horizontal transport motor encoder (M6). Press
Start. Manually rotate the drive gears forward and backward. The display changes.
Y N
Go to WD 8.5. Check horizontal transport motor (M6), MOT82-003. Refer to:
• GP 10 How to Check a Motor.
• PJ905, Media path driver PWB.
• 01D +5V Distribution RAP.
• 01J +50V Distribution RAP.
• 01L 0V Distribution RAP
Install new components as necessary:
• Horizontal transport motor (M6),
• Media path driver PWB, PL 1.15 Item
Check the horizontal transport rolls and nip rolls.
NOTE: Calibration of the registration / preheat assembly, dC625, is only required when:
• The registration / preheat assembly is removed or replaced.
• The horizontal transport assembly is removed or replaced.
Calibration of the registration / preheat assembly is NOT required when:
• A printhead is replaced.
• The IOD assembly is removed or replaced.
Status Indicator RAPs
89-110-00 to 89-113-00, 89-129-00, 89-125-00 to 89-
PL 82.15 Item 9.
5.
PL 82.10 / PL 82.15.
PL 82.15 Item 9.
5.
PL 82.15 Item 10.
89-125-00 to 89-128-00, 89-130-00, 89-131-00 Media Path
Sensor 20 Failure RAP
89-125-00 The sheet is too long over media path sensor 20 at pre-transfix.
89-126-00 The sheet is too short over media path sensor 20 at pre-transfix.
89-127-00 The leading edge was late at media path sensor 20 at pre-transfix.
89-128-00 The trailing edge was late at media path sensor 20 at pre-transfix.
89-130-00 The lead edge of the sheet was too early at media path sensor 20.
89-131-00 The media path sensor 20 static jam, sensor may be dusty.
Initial Actions
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to
death or injury. Moving parts can cause injury
• Check the registration transport for contamination or paper debris.
• Check for shingled or multi-feed sheets. Go to
priate tray.
Procedure
Clean the pre transfix sensor 20,
Y N
Perform SCP 5 Final Actions.
Enter dC330 code 89-006 pre transfix sensor (20), Q89-006. Press Start. Manually actuate the
sensor. The display changes.
Y N
Go to WD 8.6. Check pre transfix sensor 20, Q89-006. Refer to:
• REP 89.1 Registration / preheat Assembly and Lower Platelet Assembly
• GP 11 How to Check a Sensor.
• PJ5, Registration / preheat IF PWB.
• 01D +5V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Pre transfix sensor (20),
• Registration / preheat IF PWB,
• Media path PWB, PL 1.15 Item
A
February 2013
2-350
WARNING
GP 14. Disconnect the power cord. Electricity can cause
OF 8 Multi-feed RAP and check the appro-
PL 88.10 Item 12 and refer to GP 27. The fault remains.
PL 88.10 Item 12.
PL 88.10 Item 10.
5.
ColorQube® 9303 Family