U4: Maintenance Monitors - YASKAWA GA700 Series Technical Manual

11.17 U: Monitors
No.
Name
(Hex.)
U3-11 ElapsedTime@1stFault
(0094)
U3-12 ElapsedTime@2ndFault
(0095)
U3-13 ElapsedTime@3rdFault
(0096)
U3-14 ElapsedTime@4thFault
(0097)
U3-15 ElapsedTime@5thFault
(080E)
U3-16 ElapsedTime@6thFault
(080F)
U3-17 ElapsedTime@7thFault
(0810)
U3-18 ElapsedTime@8thFault
(0811)
U3-19 ElapsedTime@9thFault
(0812)
U3-20 ElapsedTime@10 Fault
(0813)
◆

U4: Maintenance Monitors

No.
Name
(Hex.)
U4-01 Cumulative Ope Time
(004C)
U4-02 Num of Run Commands
(0075)
582
V/f CL-V/f OLV CLV AOLV
Shows the cumulative operation time when the most recent fault occurred.
Note:
The drive saves this cumulative operation time to two types of registers at the same time for
the MEMOBUS/Modbus communications.
Unit: 1 h
V/f CL-V/f OLV CLV AOLV
Shows the cumulative operation time when the second most recent fault occurred.
Note:
The drive saves this cumulative operation time to two types of registers at the same time for
the MEMOBUS/Modbus communications.
Unit: 1 h
V/f CL-V/f OLV CLV AOLV
Shows the cumulative operation time when the third most recent fault occurred.
Note:
The drive saves this cumulative operation time to two types of registers at the same time for
the MEMOBUS/Modbus communications.
Unit: 1 h
V/f CL-V/f OLV CLV AOLV
Shows the cumulative operation time when the fourth most recent fault occurred.
Note:
The drive saves this cumulative operation time to two types of registers at the same time for
the MEMOBUS/Modbus communications.
Unit: 1 h
V/f CL-V/f OLV CLV AOLV
Shows the cumulative operation time when the fifth most recent fault occurred.
Unit: 1 h
V/f CL-V/f OLV CLV AOLV
Shows the cumulative operation time when the sixth most recent fault occurred.
Unit: 1 h
V/f CL-V/f OLV CLV AOLV
Shows the cumulative operation time when the seventh most recent fault occurred.
Unit: 1 h
V/f CL-V/f OLV CLV AOLV
Shows the cumulative operation time when the eighth most recent fault occurred.
Unit: 1 h
V/f CL-V/f OLV CLV AOLV
Shows the cumulative operation time when the ninth most recent fault occurred.
Unit: 1 h
V/f CL-V/f OLV CLV AOLV
Shows the cumulative operation time when the tenth most recent fault occurred.
Unit: 1 h
V/f CL-V/f OLV CLV AOLV
Shows the cumulative operation time of the drive.
Use parameter o4-01 [Elapsed Operating Time Setting] to reset this monitor. Use parameter o4-02
[Elapsed Operating Time Selection] to select the cumulative operation times from:
• The time from when the drive is energized until it is de-energized.
• The time at which the Run command is turned ON.
The maximum value that the monitor will show is 99999. After this value is more than 99999, the
drive automatically resets it and starts to count from 0 again.
Unit: 1 h
Note:
The MEMOBUS/Modbus communication data is shown in 10 h units. Use register 0099H for
data in 1 h units.
V/f CL-V/f OLV CLV AOLV
Shows how many times that the drive has received a Run command.
Use parameter o4-13 [RUN Command Counter @ Initialize] to reset this monitor. The maximum
value that the monitor will show is 65535. After this value is more than 65535, the drive
automatically resets it and starts to count from 0 again.
Unit: 1
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
YASKAWA SIEPC71061705H GA700 Series Technical Manual
MFAO Signal Level
No signal output available
No signal output available
No signal output available
No signal output available
No signal output available
No signal output available
No signal output available
No signal output available
No signal output available
No signal output available
MFAO Signal Level
10 V: 99999 h
10 V: 65535 times