YASKAWA GA700 Series Technical Manual page 542

11.10 H: Terminal Functions
No.
Name
(Hex.)
H3-18 Terminal A3 Offset
(02F2)
H3-40 Mbus Reg 15C1h Input
Function
(0B5C)
H3-41 Mbus Reg 15C2h Input
Function
(0B5F)
H3-42 Mbus Reg 15C3h Input
Function
(0B62)
H3-43 Mbus Reg Inputs
FilterTime Const
(117F)
■
H3-xx: MFAI Setting Values
Setting Value Function
0 Frequency Reference
1 Frequency Gain
2 Auxiliary Frequency
Reference 1
3 Auxiliary Frequency
Reference 2
4 Output Voltage Bias
5 Accel/Decel Time Gain
6 DC Injection Braking
Current
7 Torque Detection Level
8 Stall Prevent Level
During Run
9 Output Frequency Lower
Limit
B PID Feedback
542
Description
V/f CL-V/f OLV CLV AOLV
Sets the offset level for analog signals input to terminal A3. Usually it is not necessary
to change this setting.
V/f CL-V/f OLV CLV AOLV
Sets the MEMOBUS AI1 function.
V/f CL-V/f OLV CLV AOLV
Sets the MEMOBUS AI2 function.
V/f CL-V/f OLV CLV AOLV
Sets the MEMOBUS AI3 function.
V/f CL-V/f OLV CLV AOLV
Sets the time constant to apply a primary delay filter to the MEMOBUS analog input
register values.
V/f CL-V/f OLV CLV AOLV
The input value from the MFAI terminal set with this function becomes the master frequency reference.
V/f CL-V/f OLV CLV AOLV
The drive multiplies the analog frequency reference with the input value from the MFAI set with this function.
V/f CL-V/f OLV CLV AOLV
Sets Reference 2 through multi-step speed reference to enable the command reference (Auxiliary Frequency
Reference 1) from the analog input terminal set here. This value is a percentage where the Maximum Output
Frequency setting is a setting value of 100%.
Note:
Parameter A1-02 [Control Method Selection] selects which parameter is the maximum output frequency.
• A1-02 ≠ 8 [EZOLV]: E1-04 [Maximum Output Frequency]
• A1-02 = 8: E9-02 [Maximum Speed]
V/f CL-V/f OLV CLV AOLV
Sets Reference 3 through multi-step speed reference to enable the command reference (Auxiliary Frequency
Reference 2) from the analog input terminal set here. This value is a percentage where the Maximum Output
Frequency setting is a setting value of 100%.
Note:
Parameter A1-02 [Control Method Selection] selects which parameter is the maximum output frequency.
• A1-02 ≠ 8 [EZOLV]: E1-04 [Maximum Output Frequency]
• A1-02 = 8: E9-02 [Maximum Speed]
V/f CL-V/f OLV CLV AOLV
Set this parameter to input a bias signal and amplify the output voltage.
V/f CL-V/f OLV CLV AOLV
Enters a signal to adjust the gain used for C1-01 to C1-08 [Acceleration/Deceleration Times 1 to 4] and C1-09
[Fast Stop Time] when the full scale analog signal (10 V or 20 mA) is 100%.
V/f CL-V/f OLV CLV AOLV
Enters a signal to adjust the current level used for DC Injection Braking when the drive rated output current is
100%.
V/f CL-V/f OLV CLV AOLV
Enters a signal to adjust the overtorque/undertorque detection level.
Note:
Use this function with L6-01 [Torque Detection Selection 1]. This parameter functions as an alternative to L6-
02 [Torque Detection Level 1].
V/f CL-V/f OLV CLV AOLV
Enters a signal to adjust the stall prevention level during run if the drive rated current is 100%.
V/f CL-V/f OLV CLV AOLV
Enters a signal to adjust the output frequency lower limit level as a percentage of the maximum output frequency.
Note:
Parameter A1-02 [Control Method Selection] selects which parameter is the maximum output frequency.
• A1-02 ≠ 8 [EZOLV]: E1-04 [Maximum Output Frequency]
• A1-02 = 8: E9-02 [Maximum Speed]
V/f CL-V/f OLV CLV AOLV
Enter the PID feedback value as a percentage of the maximum output frequency.
Note:
Parameter A1-02 [Control Method Selection] selects which parameter is the maximum output frequency.
• A1-02 ≠ 8 [EZOLV]: E1-04 [Maximum Output Frequency]
• A1-02 = 8: E9-02 [Maximum Speed]
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
YASKAWA SIEPC71061705H GA700 Series Technical Manual
Default
Ref.
(Range)
0 850
(-500 - +500)
F 850
(4 - 2F)
F 850
(4 - 2F)
F 851
(4 - 2F)
0.00 s 851
(0.00 - 2.00 s)
Ref.
851
851
851
851
852
852
852
853
853
853
853