YASKAWA GA700 Series Technical Manual page 714

12.4 C: Tuning
Note:
• Set the stall prevention level during acceleration with L3-02 and the stall prevention level during run with L3-06.
• Changing C6-01 also changes the maximum capacity of applicable drive motors. The drive automatically changes the setting values
E2-xx and E4-xx to applicable values. The drive also automatically changes these parameters that depend on motor output:
–b8-04 [Energy Saving Coefficient Value]
–C5-17 [Motor Inertia]
–C5-37 [Motor 2 Inertia]
–L2-03 [Minimum Baseblock Time]
–L3-24 [Motor Accel Time @ Rated Torque]
–n5-02 [Motor Inertia Acceleration Time]
■
C6-02: Carrier Frequency Selection
No.
Name
(Hex.)
C6-02 Carrier Frequency Selection
(0224)
Changes to the switching frequency will decrease audible noise and decrease leakage current.
Note:
Increasing the carrier frequency to more than the default setting will automatically decrease the drive current rating.
1 : 2.0 kHz
2 : 5.0 kHz (4.0 kHz for AOLV/PM)
3 : 8.0 kHz (6.0 kHz for AOLV/PM)
4 : 10.0 kHz (8.0 kHz for AOLV/PM)
5 : 12.5 kHz (10.0 kHz for AOLV/PM)
6 : 15.0 kHz (12.0 kHz for AOLV/PM)
7 : Swing PWM4 (Audible Sound 1)
8 : Swing PWM4 (Audible Sound 2)
9 : Swing PWM4 (Audible Sound 3)
A : Swing PWM4 (Audible Sound 4)
F : User Defined (C6-03 to C6-05)
Use C6-03 to C6-05 to set detailed setting values.
Note:
• The carrier frequency for Swing PWM 1 to 4 is equivalent to 2.0 kHz. Swing PWM applies a special PWM pattern to decrease the
audible noise.
• The setting range changes when the A1-02 [Control Method Selection] value changes:
–3, 5, 7, 8 [CLV, OLV/PM, CLV/PM, EZOLV]: You cannot set to 7 to A.
–4 [AOLV]: You cannot set to 6, 7 to A, or F.
–6 [AOLV/PM]: You cannot set to 7 to A, or F.
Symptom
Speed and torque are not stable at low speed.
Speed and torque are not stable at low speed.
Too much leakage current from the drive.
Wiring between the drive and motor is too long.
Audible motor noise is too loud.
Wiring Distance
C6-02 [Carrier Frequency Selection]
714
V/f CL-V/f OLV CLV
Sets the carrier frequency for the transistors in the drive.
Table 12.39 Guidelines for Carrier Frequency Parameter Setup
Decrease the carrier frequency.
Decrease the carrier frequency.
Decrease the carrier frequency.
Decrease the carrier frequency.
Note:
If the motor cable is too long, it can be necessary to decrease the carrier frequency. Refer to
wiring distance and decrease the carrier frequency.
Increase the carrier frequency. Use Swing PWM.
Note:
The default carrier frequency in ND is Swing PWM 1 (C6-02 = 7), with a 2 kHz base. You can increase the
carrier frequency in Normal Duty mode, but this will decrease the drive rated current.
Table 12.40 Wiring Distance
Up to 50 m
1 to F (up to 15 kHz)
Description
AOLV OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Remedy
Up to 100 m
1 to 2 (up to 5 kHz), 7
YASKAWA SIEPC71061705H GA700 Series Technical Manual
Default
(Range)
Determined by A1-02, C6-
01, and o2-04
(Determined by A1-02)
Table 12.40 for the
Greater than 100 m
1 (up to 2 kHz), 7