YASKAWA GA700 Series Technical Manual page 596

11.18 Parameters that Change from the Default Settings with A1-02 [Control Method Selection]
No. Name
Encoder 1 Pulse Count
F1-01
(PPR)
Encoder 1 Rotation
F1-05
Selection
Overspeed Detection
F1-09
Delay Time
Motor Overload (oL1)
L1-01
Protection
KEB Start Voltage
L2-31
Offset Level
Stall Prevention during
L3-05
RUN
DC Bus Voltage
L3-20
Adjustment Gain
OVSuppression Accel/
L3-21
Decel P Gain
Current Suppression
L3-36
Gain@Accel
Speed Agree Detection
L4-01
Level
Speed Agree Detection
L4-02
Width
Speed Agree Detection
L4-03
Level(+/-)
Speed Agree Detection
L4-04
Width(+/-)
Carrier Frequency
L8-38
Reduction
Carrier Freq Reduction
L8-40
Off-Delay
STPo Detection Level
L8-90
(Low Speed)
PWM Voltage Offset
n1-15
Calibration
Speed Response
n5-04
Frequency
Initial Pole Detection
n8-35
Method
Pull-in Current @
n8-51
Acceleration
Frequency Display
o1-03
Unit Selection
V/f Pattern Display
o1-04
Unit
*1 The default setting is different for different models.
• 2138 - 2415, 4089 - 4675: 0.30
*2 The default setting changes when the setting for o2-04 [Drive Model Selection] changes.
*3 The setting range is 0.0 to 100.0 when A1-02 = 6 or 7 [PM Advanced Open Loop Vector or PM Closed Loop Vector].
*4 The setting range is 0.0 to 40.0 when A1-02 = 6 or 7 [PM Advanced Open Loop Vector or PM Closed Loop Vector].
*5 The default setting changes when C6-01 [Normal / Heavy Duty Selection] changes.
*6 The maximum value changes when A1-02 changes:
• When A1-02 = 5 [PM Open Loop Vector], the maximum value is 590.0 Hz. The maximum value of the setting range changes
when E5-01 [PM Motor Code Selection] changes. When E5-01 = FFFF [PM Motor Code Selection = FFFF], the maximum
value is 590.0 Hz.
• When A1-02 = 6 or 7 [PM Advanced Open Loop Vector or PM Closed Loop Vector], the maximum value is 400.0 Hz. The
maximum value of the setting range changes when E5-01 changes. When E5-01 = FFFF, the maximum value is 400.0 Hz.
*7 This is the value for 200 V class drives. Double the value for 400 V class drives.
The default setting changes when E9-01 [Motor Type Selection] changes.
*8
• E9-01 = 0 [Induction (IM)]: 1
• E9-01 = 1, 2 [Permanent Magnet (PM), Synchronous Reluctance (SynRM)]: 4
*9 The default setting changes when E9-01 [Motor Type Selection] changes.
• E9-01 = 0 [Induction (IM)]: 0
• E9-01 = 1, 2 [Permanent Magnet (PM), Synchronous Reluctance (SynRM)]: 1
596
Range Unit
0 - 60000 1 ppr
0 - 1 1
0.0 - 2.0 0.1 s
0 - 6 1
*7
0 - 100 1 V
0 - 3 1
0.00 - 5.00 0.01
0.10 - 10.00 0.01
0.0 - 100.0 0.1
*10
0.0 - 590.0 0.1
*4
0.0 - 20.0 0.1
*10
-590.0 - +590.0
0.1
*11
*4
0.0 - 20.0 0.1
0 - 2 1
0.00 - 2.00 0.01 s
0 - 5000 1
0 - 2 1
0.00 - 500.00 0.01 Hz
0 - 2 1
0 - 200 1%
0 - 3 1
0 - 1 1
Control Method (A1-02 Setting)
OLV/PM AOLV/PM
(5) (6)
- -
- -
- 0.0
4 4
50 50
1 -
0.65 0.65
1.00 1.00
- -
0.0 Hz 0.0%
2.0 Hz 4.0%
0.0 Hz 0.0%
2.0 Hz 4.0%
0 -
0.00 -
0 80
1 1
- 20.00
0 1
50% -
0 1
- 1
YASKAWA SIEPC71061705H GA700 Series Technical Manual
CLV/PM EZOLV
(7) (8)
1024 -
1 -
0.0 0.0
*8
5 1
50 50
- 3
0.65 0.65
1.00 1.00
- -
0.0% 0.0 Hz
4.0% 2.0 Hz
0.0% 0.0 Hz
4.0% 2.0 Hz
0 0
0.00 0.00
- 0
1 1
50.00 -
1 -
- 80%
*9
1 0
*9
1 0