YASKAWA GA700 Series Technical Manual page 535

Setting Value Function
33 Zero Servo Complete
37 During Frequency
Output
38 Drive Enabled
39 Watt Hour Pulse Output
3C LOCAL Control
Selected
3D During Speed Search
3E PID Feedback Low
3F PID Feedback High
4A During KEB Ride-Thru
4B During Short Circuit
Braking
4C During Fast Stop
4D oH Pre-Alarm Time
Limit
4E Braking Transistor Fault
(rr)
4F Braking Resistor
Overheat (rH)
60 Internal Cooling Fan
Failure
61 Pole Position Detection
Complete
62 Modbus Reg 1 Status
Satisfied
63 Modbus Reg 2 Status
Satisfied
65 Standby Output
66 Comparator1
67 Comparator2
YASKAWA SIEPC71061705H GA700 Series Technical Manual
V/f CL-V/f OLV CLV AOLV
The terminal activates when positioning in the range set with b9-02 [Zero Servo Completion Window] completes
after sending the Zero-Servo command.
V/f CL-V/f OLV CLV AOLV
The terminal activates when the drive outputs frequency.
ON : The drive is outputting frequency.
OFF : The drive is not outputting frequency.
V/f CL-V/f OLV CLV AOLV
This terminal activates when the H1-xx = 6A [Drive Enable] terminal activates.
V/f CL-V/f OLV CLV AOLV
Outputs the pulse that shows the watt hours.
V/f CL-V/f OLV CLV AOLV
The terminal activates when the Run command source or frequency reference source is LOCAL.
ON : LOCAL
OFF : REMOTE
V/f CL-V/f OLV CLV AOLV
The terminal activates when the drive is doing speed search.
V/f CL-V/f OLV CLV AOLV
The terminal activates when the drive detects FbL [PID Feedback Loss].
V/f CL-V/f OLV CLV AOLV
The terminal activates when the drive detects FbH [Excessive PID Feedback].
V/f CL-V/f OLV CLV AOLV
The activates during KEB Ride-Thru.
V/f CL-V/f OLV CLV AOLV
The terminal activates during Short Circuit Braking.
Note:
When A1-02 = 8 [Control Method Selection = EZOLV], this function is available only when you use a PM
motor.
V/f CL-V/f OLV CLV AOLV
The terminal activates when the fast stop is in operation.
V/f CL-V/f OLV CLV AOLV
The terminal activates when L8-03 = 4 [Overheat Pre-Alarm Selection = Operate at Reduced Speed (L8-19)] and
oH [Heatsink Overheat] does not clear after the drive decreases the frequency for 10 cycles.
V/f CL-V/f OLV CLV AOLV
The terminal activates when the internal braking transistor overheats and the drive detects an rr [Dynamic Braking
Transistor Fault] fault.
V/f CL-V/f OLV CLV AOLV
The terminal activates when the braking resistor overheats and the drive detects an rH [Braking Resistor Overheat]
fault.
V/f CL-V/f OLV CLV AOLV
The terminal activates when the drive detects a cooling fan failure in the drive.
V/f CL-V/f OLV CLV AOLV
The terminal activates when drive receives a Run command and the drive detects the motor magnetic pole position
of the PM motor.
V/f CL-V/f OLV CLV AOLV
The terminal activates when the bit specified by H2-08 [Modbus Register 1 Bit Select] for the MEMOBUS register
address set with H2-07 [Modbus Register 1 Address Select] activates.
V/f CL-V/f OLV CLV AOLV
The terminal activates when the bit specified by H2-10 [Modbus Register 2 Bit Select] for the MEMOBUS register
address set with H2-09 [Modbus Register 2 Address Select] activates.
V/f CL-V/f OLV CLV AOLV
The terminal deactivates after the drive stops operating and after the time set with b8-51 [Standby Mode Wait
Time].
ON : The Run command turns on and the magnetic contactor on the input side turns on.
OFF : The Run command turns off and the drive stops operating. Then, the magnetic contactor on the input side
turns off after the time set in b8-51 [Standby Mode Wait Time] elapses.
V/f CL-V/f OLV CLV AOLV
The terminal activates if the monitor value set with H2-20 [Comparator 1 Monitor Selection] is in range of the
values of H2-21 [Comparator 1 Lower Limit] and H2-22 [Comparator 1 Upper Limit] for the time set in H2-24
[Comparator 1 On-Delay Time].
V/f CL-V/f OLV CLV AOLV
The terminal activates if the monitor value set with H2-26 [Comparator 2 Monitor Selection] is not in the range of
the values of H2-27 [Comparator 2 Lower Limit] and H2-28 [Comparator 2 Upper Limit] for the time set in H2-
30 [Comparator 2 On-Delay Time].
Description
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
11.10 H: Terminal Functions
Ref.
840
840
840
841
841
841
841
841
841
842
842
842
842
842
842
842
842
842
843
843
843
11
535