H4: Analog Outputs - YASKAWA GA700 Series Technical Manual

12.8 H: Terminal Functions
Note:
When you use L7-01 to L7-04 and analog inputs to set torque limits for the same quadrant, it will enable the lower torque limit.
■
13: Torque Reference / Torque Limit
Setting Value Function
13 Torque Reference / Torque
Limit
Note:
When you use L7-01 to L7-04 and analog inputs to set torque limits for the same quadrant, it will enable the lower torque limit.
■
14: Torque Compensation
Setting Value Function
14 Torque Compensation
■
15: General Torque Limit
Setting Value Function
15 General Torque Limit
■
16: Differential PID Feedback
Setting Value Function
16 Differential PID Feedback
The drive uses the deviation between the PID feedback and the differential feedback value signals to calculate the
PID input.
■
1F: Not Used
Setting Value Function
1F Not Used
When you set a terminal that you do not use to 1F, you can use the signal that is input to that terminal as the PLC
analog signal input from MEMOBUS/Modbus communications or the communication option. This input signal
does not have an effect on drive operation. This signal functions the same as F (Through Mode).
■
30: DWEZ Analog Input 1
Setting Value Function
30 DWEZ Analog Input 1
■
31: DWEZ Analog Input 2
Setting Value Function
31 DWEZ Analog Input 2
■
32: DWEZ Analog Input 3
Setting Value Function
32 DWEZ Analog Input 3
◆

H4: Analog Outputs

H4 parameters set the drive analog monitors. These parameters select monitor parameters, adjust gain and bias,
and select output signal levels.
856
V/f CL-V/f OLV CLV AOLV
Enters the torque reference if the motor rated torque is 100%. This setting is the torque limit for speed control.
V/f CL-V/f OLV CLV AOLV
Enters the torque compensation value if the motor rated torque is 100%.
V/f CL-V/f OLV CLV AOLV
Enters the torque limit that is the same for all quadrants for forward, reverse, and regenerative operation if the motor rated
torque is 100%.
V/f CL-V/f OLV CLV AOLV
Enters the PID differential feedback value if the full scale analog signal (10 V or 20 mA) is 100%.
V/f CL-V/f OLV CLV AOLV
Use this setting for unused terminals or to use terminals in through mode.
V/f CL-V/f OLV CLV AOLV
Use with DriveWorksEZ. Refer to the DriveWorksEZ online manual for more information.
V/f CL-V/f OLV CLV AOLV
Use with DriveWorksEZ. Refer to the DriveWorksEZ online manual for more information.
V/f CL-V/f OLV CLV AOLV
Use with DriveWorksEZ. Refer to the DriveWorksEZ online manual for more information.
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
Description
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Description
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
YASKAWA SIEPC71061705H GA700 Series Technical Manual